INSTRUCTIONS FOR USE MODEL SC400
Using KENWOOD STEAM MOP is really very simple:
1.Once the appliance has been unpacked, fit the extension tube in the appliance’s body and then extend it to the desired length (fig. 1).
2.Fix the top part of the tube by turning it in a clockwise direction (fig. 2).
3.Fix the cord into the hook which is provided along the tube (fig. 3)
4.Rest the base of KENWOOD STEAM MOP on the floorcloth, secure the floor cloth to the KENWOOD STEAM MOP using the Velcro straps, making sure the cloth is secured on the base (fig. 4).
5.Unscrew the cap (D) and pour 2 measuring jugs (I) of water into the tank using the provided funnel (L) (fig. 5). Then screw the safety cap on tightly. Now insert the plug into the power outlet.
6.Place the Steam Mop on the provided preheat tray. Press the switch (C), the pilot light (E) will go on (fig. 6). Do not leave the appliance unattended while you are waiting for the Steam Mop to heat up.
7.When steam starts coming out, slowly run the appliance over the surfaces to be cleaned. This way your floors will become perfectly clean.DO NOT LEAVE in one spot for more than 15 seconds as it may cause a whitish halo to form on the surface. This is no call for concern as it may be removed using a normal decalcifying product or with a few drops of vinegar directly onto the floor.
8.When Steam Mop stops producing steam and the water exhaustion light (F) goes on it means that the water has run out (approximately every 15 minutes use). In this case, press the switch (C), unplug the appliance and refill with water as described at point 5. During this operation, mind not to touch the appliances hot parts.
9.Press the switch (C) again. Steam Mop will restart producing steam.
10.When finished wash the cloth with water and soap or in washing machine.Every time you replace the cloth, turn off the switch (C) and do not touch the appliances hot parts.
11.After using and before putting the appliance away, wind the power cord around the provided hooks (see fig. 7) and empty any water left in the tank of the Steam Mop. Before using the appliance again, unwind the power cord completely. Be sure the power cord is completely unwound before you plug it in.
CLEANING AND MAINTENANCE
The following operation must be carried out only if the appliance is unplugged from its power source.
In order to guarantee perfect functioning over a long period of time the tank needs to be rinsed out at least once a week with cold water to eliminate any accumulated calcium deposits.
DO NOT USE VINEGAR OR OTHER DECALCIFYING SUBSTANCES.
KENWOOD STEAM MOP does not need to be used with its own specially developed floor cloths but can be used with the floor cloths that you normally use in your home.
Spare floor cloths are available by mail order from Hagemeyer.
Attention.
Before washing the Magic Cloth, Kenwood recommends the Magic Cloth straps be neatly joined together to avoid lint clogging the magic tape hooks.
|
|
|
|
|
|
| PROBLEM | CAUSE | SOLUTION |
|
|
|
|
|
|
|
|
|
|
|
| ||
Appliance | * Electric plug | *Push plug securely into outlet |
| ||
won’t start |
| *Try another outlet |
| ||
|
|
| *Check circuit breaker |
| |
|
| * Power switch not turned on | *Make sure power switch is on |
| |
|
| * No water in tank | *Check the tank for water |
| |
|
|
|
|
|
|
Appliance won’t make steam | *No water in tank | *Check the tank for water |
| ||
|
|
|
|
|
|
Appliance leaves water on the floor | *Floorcloth is too wet | *Change floorcloth |
| ||
|
|
| *If wood floor, dry the floor before proceeding. | ||
|
|
| *Too much water in tank, Do not | overfill | |
|
| *Appliance did not remain flat on surface | *Turn off, unplug from electrical | outlet, change | |
|
| while turned on | floorcloth and reheat appliance. |
| |
|
|
|
|
| |
Appliance leaves a whitish halo on | *Left in one spot too long | *Remove with few drops of vinegar. | |||
floor |
| *If above step doesn’t remove halo, then reheat | |||
|
|
| area for one minute and discoloration will be | ||
|
|
| removed. Do not overheat area. |
| |
|
|
|
|
|
|
