Kenwood TK-7102H Adjustment Location

TK-7102H

ADJUSTMENT

Adjustment Location

■Switch

■Adjustment Points

■Notes

•EEPROM

The tuning data (Deviation, Squelch, etc.) for the EEP-

ROM, is stored in memory. When parts are changed, re-

adjust the transceiver.

•AF PA IC (IC252)

How to mounting the IC252.

•Speaker Cable

The speaker cable should be formed before mounting the

shield cover as below.

•Fuse

To mount the fuse, the cable terminal direction must be as

follow.

LocatorSpeakercable

This side up This side up

Cable terminal Cable terminal

Fuse

Pin 1 marker

IC252

Part name label face down

TX-RX UNIT

Component side

Power

MIC jack 1/2/3/4 keys

Volume

up/down

key

key Speaker

Display

R518

F501

Q503

Q504

IC252

R516

R524

CNVSS

RESET

POWER

E+B

RXDTXD

IGN

BPF

TEMP1

AFV

TEMP2

TX-RX unit

Component side

VR1

ANT

TC401

TC402

L301

TC351

TC352

E+B

BPF

TX-RX unit

Foil side

Contents

Main TK-7102H SERVICE MANUAL CONTENTS REVISED TK-7102H GENERAL INTRODUCTION SCOPE OF THIS MANUAL ORDERING REPLACEMENT PARTS GENERAL / SYSTEM SET-UP SYSTEM SET-UP 1-5. Rear panel 1. Controls and Functions 1-4. Display o 1-2. Microphone 1-1. Front Panel 2. Operation Features 3. Transceiver Controls and Indicators 4. Scan Operating SCAN start condition Scan stop condition Revert channel Scan end TK-7102H SP Unmute Auto Reset Stun 7. Audible User Feedback Tones REALIGNMENT 1. Modes 2. How to Enter Each Mode 3. PC Mode 3-1. Preface REALIGNMENT 5. Accessory Connection Cable (KCT-39) 5-1. Installing the KCT-39 in the Transceiver Fig. 3 TK-7102H ) into the chassis ( Fig. 7 Accessory Port Function Fig. 6 REALIGNMENT / INSTALLATION 6-3. Modifying the Transceiver Fig. 2 R267 Fig. 8 INSTALLATION Fig. 4 Fig. 3 Setting With the KPG-70D Select External Devices from the Edit menu and set the Scrambler. DISASSEMBLY FOR REPAIR Frequency Configuration Fig. 1 Frequency configuration Fig. 2 Receiver system Receiver System Front-end RF Amplifier CIRCUIT DESCRIPTION Wide/Narrow Changeover Circuit Fig. 6 PLL circuit Fig. 4 AF signal system AF Signal System Transmitter System Outline Power Amplifier Circuit APC Circuit Control Circuit Memory Circuit Fig. 14 Encodet Fig. 13 Key matrix circuit Fig. 12 Display circuit CIRCUIT DESCRIPTION / SEMICONDUCTOR DATA SEMICONDUCTOR DATA Drive Amplifier : PD55003TR (TX-RX Unit Q503) Absolute Maximum Ratings (TCASE = 25C) SEMICONDUCTOR DATA Microprocessor : 30622MAA-B83GP (TX-RX Unit IC101) Terminal Function COMPONENTS DESCRIPTION Display Unit (X54-3460-20) TX-RX Unit (X57-6700-XX) TK-7102H TX-RX UNIT (X57-6700-XX) -22 : M -23 : M2 -24 : K -25 : K2 DISPLAY UNIT (X54-3460-20) Page Page Page Page Page EXPLODED VIEW PACKING Parts with the exploded numbers larger than 700 are not supplied. Test Equipment Required for Alignment Tuning cable (E30-3383-05) MIC connector (Front view) Test cable for microphone input (E30-3360-08) Adjustment Location Switch Part name label face down Fuse Locator PCB Section * Adjustment of TX VCO lock voltage K,M K2,M2 Test Frequency (MHz) Receiver Section Transmitter Section If normal power is not obtained, please follow the step below TERMINAL FUNCTION CN2 Function Port Assignment CN3 CN4 PC BOARD TK-7102H DISPLAY UNIT (X54-3460-20) Component side view (J72-0916-09) DISPLAY UNIT (X54-3460-20) Foil side view (J72-0916-09) ABCDEFGHIJ KLM NOPQRS TK-7102H 37 38 S RQP O NMLK J IHGF PC BOARD TK-7102H 39 40 ABCDEFGHIJ KLM NOPQRS Ref. No. TK-7102H 41 42 46 1 * SCHEMATIC DIAGRAM TK-7102H Note : The components marked with a dot () are parts of layer 1. X57-6700-XX TX-RX UNIT X54-3460-20 DISPLAY UNIT M P TK-7102H TK-7102 H 47 48 BLOCK DIAGRAM TX-RX UNIT (X57-670x-xx) DISPLAY UNIT (X54-3460-20) TK-7102H TK-7102H 49 50 LEVEL DIAGRAM Transmitter Section 4 SPECIFICATIONS 51 GENERAL RECEIVER TRANSMITTER KENWOOD CORPORATION