D ISHWASHER
How to use your Dishwasher
First of all.
-Turn on the water supply tap completely.
-Add the correct amount of detergent.
-Load the baskets correctly.
-Check that the spray arms rotate freely.
-Close the door securely.
-Press the
Yourapplianceisnowonandawait- ing instructions.
Select the wash cycle. Select the wash cycle by pressing button "P". Each time this button is pressed,abeepwillsoundandindi- cator lights “E” will come on in sequence.Select the wash cycle most suitable for the type of dishes to wash (see ‘Programme Chart’). Close the door and press the Start button after a few seconds, you will hear a short beep and the wash cy- cle will started.
The dishwasher informs you.
Yourdishwasherhasindicatorlights "G" which light up to indicate the washcyclephasethatisunderway.
Modifying a wash cycle in progress.
Ifyouhavechosenthewrongcycle
-You can modify the wash cycle in progress, if it has only just started. KeeptheResetbutton "R"pressed in for approximately 5 seconds, a prolongedbeepwillsound,followed by three short beeps.
Indicator light "G" will go out to show all the settings will have been cancelled. You are now free to re- set the correct wash cycle.
You've left out a dish? Interrupt the wash cycle by press- ing the
Cycle end
The end of the wash cycle is indi- cated by 2 short beeps and the flashing of the drying phase indica- torlight.
Turn the appliance off by pressing the
Turn off the water tap.
Wait a few minutes before unload- ing the dishes: they are very hot! If youwaitalittlewhile,theydrybetter due to the steam.
Empty the lower basket first.
There's been a power failure or you opened the dishwasher door
The wash cycle stops and then restarts when the electricity comes backonorwhenyouclosethedoor.
Delaying the start of a programme.
Whenyouhaveloadedthedishes, youcanchoosewhentostartyour dishwasherbeforesettingthewash cycledesired.
Pressbutton"D"todelaythestart of the wash cycle by 12, 9, 6 or 3 hours.Eachtimeyoupressit,you willhearashortbeepandindicator light "G" corresponding to the selecteddelaywillcomeon.
Selectthedesiredwashcycle. PresstheStartbutton,youhearthe beep,thecountdowntothedelayed startwillbegin.
If, for example, you have set a 12 hourdelay,onceyouhaveselected awashcyclethe12hourindicator lightwillflash...followedbytheothers insequenceuntilthesettimedelay isup.Theindicatorlightswillkeep you informed of the countdown progressatalltimes.
Oncethistimeisup,indicatorlight "G"willstopflashingandthewash cyclewillbegin.
If you change your mind and you wishtosetadifferentdelay,justopen thedoor,pressbutton"D",youneed notresetthewashcycle.
If you want to cancel the delay set andyouwishtostartthewashcycle immediately, press button "D" repeatedlyuntilthecyclestartsand indicatorlight"G"correspondingto thecyclestartphasecomeson.
Cycle phase and delayed start indicator light "G"
(1)Flashing to indicate a delayedstart,toremindyouthatyou have set a delayed start.
(2)On,litconstantly,eachlight shows which stage of the wash cycle is in progress.
Half load.
Yourdishwasheralsoallowsyouto wash half a load, to save water , electricityanddetergent(useonly halftheamount).
Beforesettingawashcycle,press button "F", indicator light "H" will comeon.
NOTE: When set the dishwasher willwashontheupperbasketonly.
To see the settings you have selected
At any time, when the cycle is underway,ifyoupressbutton"F", thecycleinprogressindicatorlight will light up for a few seconds...
followedbythehalfloadindicatorlight ifset.
For your own safety, ensure the door is closed when the dishwasher is not in use.
12