Manuals / Brands / Household Appliance / Home Security System / Kenwood / Household Appliance / Home Security System

Kenwood TK-8180 Common Section, Transmitter Section (K market model skips adjustment of Wide 4k)

1 85

Download 85 pages, 3.04 Mb

TK-8180

39

Item Condition

Measurement Adjustment

Specifications/Remarks

Test-

equipment Unit Terminal PartsUnit Method

ADJUSTMENT

1. Setting 1) Power supply voltage

DC power supply terminal : 13.6V

2) SSG standard modulation

[Wide 5k] MOD : 1kHz, DEV : 3kHz

[Wide 4k] MOD : 1kHz, DEV : 2.4kHz

[Narrow] MOD : 1kHz, DEV : 1.5kHz

2. VCO lock [Panel test mode]

Power meter

Rear ANT TX-RX TC301 8.1V ±0.1V

voltage 1) CH-Sig : 3-1 panel (B/3)

• RX

2) CH-Sig : 2-1 DVM TX-RX CV Check 1.5V±0.5V

(B/3)

• TX [Panel tuning mode] LPWR* TX-RX TC302 8.1V ±0.1V

3) CH-Sig : 3-1 (B/3)

PTT : ON

4) CH-Sig : 2-1 Check 1.5V±0.5V

PTT : ON

* TX can be continued on unlock condition in panel tuning mode.

1. Frequency 1) Adj item : [FREQ] f. counter Rear ANT Front [ ],[ ]Center frequency Note : After replacing the

adjust Adjust : [✳✳✳]panel panel ±100Hz VCXO (X301) align frequency.

PTT : ON

2. Frequency 1) Adj item : [SHFT1] [L SHFT1] ±100Hz

shift 1 Adjust : [✳✳✳]

Low frequency+5.00kHz

adjust 2) Adj item : [L SHFT1] → [C SHFT1]

[C SHFT1] → [H SHFT1]

Center frequency+5.00kHz

Adjust : [✳✳✳][H SHFT1]

PTT : ON

High frequency+5.00kHz

3. Frequency 1) Adj item : [SHFT2] [L SHFT2] ±100Hz

shift 2 Adjust : [✳✳✳]

Low frequency+6.25kHz

adjust 2) Adj item : [L SHFT2] → [C SHFT2]

[C SHFT2] → [H SHFT2]

Center frequency+6.25kHz

Adjust : [✳✳✳][H SHFT2]

PTT : ON

High frequency+6.25kHz

4. Max high 1) Adj item : [MHPWR]

Power meter

[L MHPWR], ±3W

power Adjust : [✳✳✳][L’ MHPWR],

adjust 2) Adj item : [L MHPWR] → [C MHPWR]

[L’ MHPWR] → [C MHPWR]→

: 33W

[H’ MHPWR] → [H MHPWR]

[H’ MHPWR],

Adjust : [✳✳✳][H MHPWR]

PTT : ON : 28W

Common Section

Item Condition

Measurement Adjustment

Specifications/Remarks

Test-

equipment Unit Terminal PartsUnit Method

Transmitter Section (K market model skips adjustment of Wide 4k)

Contents

Main UHF FM TRANSCEIVER TK-8180 SERVICE MANUAL CONTENTS GENERAL INTRODUCTION SCOPE OF THIS MANUAL ORDERING REPLACEMENT PARTS PERSONAL SAFETY GENERAL / SYSTEM SET-UP Speaker jack cap SYSTEM SET-UP D-sub cap Power input connector 1. Modes 2. How to Enter Each Mode Fig. 1 3. Panel Test Mode Setting method refer to ADJUSTMENT. 6. Firmware Programming Mode 6-1. Preface 6-2. Connection procedure Note : 6-3. Programming 8. Firmware Version Information 9. Clock Adjustment Mode Fig. 2 9-1. Flow chart of operation 2. Radio Interface Cable (KCT-40 : Option) 2-1. Connecting the KCT-40 cable to the transceiver w q e 2-2. Terminal function TK-8180 3. Horn Alert/P.A. Relay Unit (KAP-2 : Option) Install the KRK-10 rear panel onto the front panel q Fig. 4-2 4. Control Head Remote Kit (KRK-10 : Option) 4-1. Installing the KRK-10 kit to the transceiver Remove the front panel from the transceiver y r t Fig. 4-1 5. Voice Guide & Storage Unit (VGS-1 : Option) 5-1. Installing the VGS-1 unit in the transceiver q w Connect the KRK-10 main panel to the rear panel with the cable 8. GPS Receiver Connection 8-1. Installing the GPS receiver Fig. 8-1 Fig. 7-1 7. ANI Board Connection 8-2. Installing the GPS receiver together with the VGS-1 Fig. 8-5 q Fig. 8-3 1. Precautions on Disassembly r e 2. Precautions on Reassembly Page 1. Outline 2. Receiver Circuit Fig. 1 Receiver circuit 2-1. Front-end Circuit 2-2. First Mixer 3. Transmitter Circuit Fig. 3 Drive and Final power amplifier and automatic power control circuit 3-1. Microphone Circuit 3-2. Modulation Level Adjustment Circuit 3-3. Driver and Final Power Amplifier Circuit TK-8180 4. Frequency Synthesizer Unit Fig. 5 Control circuit block diagram Fig. 4 PLL block diagram 4-1. Frequency Synthesizer 6. Power Supply Circuit 7. Display Circuit Fig. 7 Display circuit Fig. 6 Power supply circuit SEMICONDUCTOR DATA Microprocesser : 30625MGP-169GP (TX-RX unit IC404) Shift Register : BU4094BCFV (TX-RX unit IC403) SEMICONDUCTOR DATA Microprocesser : 30302M8-8Z7GP (Display unit IC902) COMPONENTS DESCRIPTION Display unit (X54-3480-10) TX-RX unit (X57-6990-10) COMPONENTS DESCRIPTION TK-8180 DISPLAY UNIT (X54-3480-10) TX-RX UNIT (X57-6990-10) Page Page Page Page Page Page Page EXPLODED VIEW PACKING Parts with the exploded numbers larger than 700 are not supplied. Controls Panel Test Mode LCD display in panel test mode This transceiver has a test mode. Test mode operation features Panel Tuning Mode Preparations for tuning the transceiver Transceiver tuning (To place transceiver in tuning mode) LCD display in panel tuning mode nBAL 256 Flow chart Note : The Wide 4k can not use, please skip it. High High 3 reference level adjustments Test Equipment Required for Alignment MIC connector (Front panel view) KENWOOD part : W05-1127-00 Test cable for microphone input (E30-3360-08) Tuning cable (E30-3383-05) Common Section Transmitter Section (K market model skips adjustment of Wide 4k) Page Page Page Receiver Section (K market model skips adjustment of Wide 4k) Page Adjustment Points Display unit (X54-3480-10) TX-RX unit (X57-6990-10) (A/3) TX-RX unit (X57-6990-10) (B/3) Page Solder Land TK-8180 DISPLAY UNIT (X54-3480-10) Component side view (J72-0932-09) DISPLAY UNIT (X54-3480-10) Foil side view (J72-0932-09) DISPLAY UNIT (X54-3480-10) Component side view (J72-0932-09) DISPLAY UNIT (X54-3480-10) Foil side view (J72-0932-09) TK-8180 TK-8180 TX-RX UNIT (X57-6990-10) (A/3) Component side view (J72-0931-19 A/3) TX-RX UNIT (X57-6990-10) (C/3) Component side view (J72-0931-19 C/3) TX-RX UNIT (X57-6990-10) (C/3) Foil side view (J72-0931-19 C/3) TX-RX UNIT (X57-6990-10) (A/3) Foil side view (J72-0931-19 A/3) J72-0931-19 B/3 TK-8180 Component side view (J72-0931-19 B/3) JKLMNOPQRSIHGFEDCBA J72-0931-19 B/3 TK-8180 Component side view (J72-0931-19 B/3) TX-RX UNIT (X57-6990-10) (B/3) Component side view (J72-0931-19 B/3) Component side Foil side Layer 1 Layer 2 Layer 3 Layer 4 TK-8180 Foil side view (J72-0931-19 B/3) JKLMNOPQRS Foil side view (J72-0931-19 B/3) Ref. No. D404 931-19 B/3 0 TK-8180 Foil side view (J72-0931-19 B/3) TX-RX UNIT (X57-6990-10) (B/3) Foil side view (J72-0931-19 B/3) Component side Foil side Layer 1 Layer 2 Layer 3 Layer 4 ABCDE X54-348 1/2 59 JIHGF Note : The components marked with a dot () are parts of layer 1. TO TX-RX UNIT (B/3) CN429 X54-348 2/2 TO TX-RX UNIT (B/3) CN429 ABCDE X57-699 1/9 TX-RX UNIT (X57-6990-10)(B/3) TO DISPLAY UNIT CN902 JIHGF X57-699 2/9 KLMNO X57-699 3/9 TSRQP X57-699 4/9 UVWXY X57-699 5/9 TX-RX UNIT (X57-6990-10)(C/3) ADACABAAZ TX-RX UNIT (X57-6990-10) (B/3) X57-699 6/9 AE AF AG AH AI X57-699 7/9 ANAMALAKAJ X57-699 8/9 68 1 2 3 4 TX-RX UNIT (X57-6990-10)(C/3) TX-RX UNIT (X57-6990-10)(B/3) TO DISPLAY UNIT CN902 TX-RX UNIT (X57-6990-10)(A/3) INTERCONNECTION DIAGRAM 69 CN701 IC1 IC417 TK-8 180 BLOCK DIAGRAM TK-8180 LEVEL DIAGRAM Receiver Section Transmitter Section LEVEL DIAGRAM 74 External View KRK-10 Parts List INTERFACE UNIT (X46-3310-20) Components Description TK-8180 Exploded View and Packing TK-8180 PC Board J72-0934-09 B/2 J72-0934-09 A/2 Component side Foil side Layer 1 Layer 2 Schematic Diagram INTERFACE UNIT (X46-3310-20) (B/2) Display Side INTERFACE UNIT (X46-3310-20) (A/2) Radio Side Terminal Function OPTIONAL ACCESSORIES SPECIFICATIONS KENWOOD CORPORATION GENERAL RECEIVER (Measurements made per EIA/TIA-603) TRANSMITTER (Measurements made per EIA/TIA-603)