Basic remote control operations for other components
Checking the codes
If you have setup the remote control using the procedures described in “Searching for your codes”, you may need to find out which
For example, to find out which code is operating your TV:
1Press the TV MODE key once. Next, press and hold the REMOTE SETUP key until the LED blinks twice, then release the REMOTE SETUP key.
2Press the Numeric key to enter 9, 9, ).
• The LED will blink twice.
3To view the code for the first digit, press “1” once. Wait for 3 seconds, counts the number of times the LED blinks (e.g., blinks=3) and write down that number.
5To clear the
1Press and hold the REMOTE SETUP key until the LED blinks twice, then release the REMOTE SETUP key.
2Press the Numeric key to enter 9, 9, 2.
3Press VIDEO 2 key twice.
•When a
•If an invalid key sequence is entered, the LED blink once and return to normal operation.
•When in Tuner mode,
•If a code digit is “0”, the LED will not blink.
4Repeat step 3 three more times for the remaining digits. Use “2” for the second digit, “3” for the third digit, and “4” for the fourth digit.
5To check the codes of your other components, repeat steps 1 through 4, but substitute the appropriate key (i.e.,
DVD/6CH, VIDEO 1, VIDEO 2, VIDEO 3, CD/DVD, MD/TAPE, PHONO, AV AUX, TV MODE) for the component you are checking.
•As suggested earlier on, write down each of the
•PHONO key has to be
Operating other components
This operation lets you operate the registered components.
SOURCE (power)
Source keys
Re-assigning device keys
The remote control can be setup to control second TV or VCR, or any combination of eight home entertainment components.
For example, to control the operation of two different VCR using the remote control, the user need to
1Press and hold the REMOTE SETUP key until the LED blinks twice, then release the REMOTE SETUP key.
2Press the Numeric key to enter 9, 9, 2.
• The LED will blink twice.
3Press VIDEO 1 key once, then press the VIDEO 2 key once.
•The user now can operate VIDEO 2 as a second VCR along with VIDEO 1.
•Refer to the table in the previous page for the combination of
source keys and the other components assignment. | › |
4To
To
Sequence | Perform |
|
|
| ||
TV MODE as 2nd VIDEO 1 key | REMOTE SETUP | 9 | 9 | 2 | VIDEO 1 | TV MODE |
TV MODE as 2nd VIDEO 2 key | REMOTE SETUP | 9 | 9 | 2 | VIDEO 2 | TV MODE |
TV MODE as 2nd CD/DVD key | REMOTE SETUP | 9 | 9 | 2 | CD/DVD | TV MODE |
TV MODE back to TV MODE key | REMOTE SETUP | 9 | 9 | 2 | TV MODE | TV MODE |
VIDEO 1 as 2nd TV MODE key | REMOTE SETUP | 9 | 9 | 2 | TV MODE | VIDEO 1 |
VIDEO 1 as 2nd VIDEO 2 key | REMOTE SETUP | 9 | 9 | 2 | VIDEO 2 | VIDEO 1 |
VIDEO 1 as 2nd CD/DVD key | REMOTE SETUP | 9 | 9 | 2 | CD/DVD | VIDEO 1 |
VIDEO 1 back to VIDEO 1 key | REMOTE SETUP | 9 | 9 | 2 | VIDEO 1 | VIDEO 1 |
1Use the Source keys to select the component you desire.
•Pressing the source keys also changes the input selector on the receiver.
2Press the SOURCE key.
•To return to the receiver operation mode, press the TUNER key for more than 3 seconds.
3Press the operation keys you desire. | ‚ |
The remote control mode remains at the selected input. If you wish to operate another component, repeat step 2 or 3.
Resetting the Remote control
•To initialize the remote control, press the REMOTE SETUP key
until the LED blinks twice. Then press the Numeric key to enter 9, 8, 1. The LED will blink twice.