Keurig B60 manual Adding Water Brewing Hot Water, Purging the Brewer, Stopping the Brew Process

SECTION 1 Set-Up & First Brew

Ready to Brew Your First Cup (Continued)

10. Lift the Handle, remove and dispose of the

used K-Cup®pack. CAUTION: K-Cup®pack

Adding Water

Brewing Hot Water

Small Cup

(5.25 oz.)

7. Choose the cup size of coffee, tea or hot

cocoa by pressing the button that indicates

your choice. The Small Cup choice will yield

a 5.25 oz. serving, the Small Mug choice will

yield a 7.25 oz. serving and the Large Mug

choice will yield a 9.25 oz. serving. NOTE: If

you do not push a Brew Button in 60 seconds,

the LCD Control Center will return to “READY

TO BREW” and the Brew Buttons will be

will be hot.

11. Enjoy your first cup of Keurig Brewed® gourmet coffee, tea or hot cocoa!

12. Your Brewer may indicate “NOT READY” as it heats water for the next brew cycle. The “READY TO BREW” indication will return to the LCD Control Center in about 15 seconds.

NOTE: Following the brew, your Brewer will

fig. 8

NOT READY

ADD

WATER

The LCD Control Center will indicate “ADD WATER” when the water level in the Water Reservoir is low or if the Water Reservoir has been removed (fig. 8). The blue light in the Water Reservoir will also blink when water needs to be added. The Brewer will not allow you to brew when “ADD WATER” is indicated.

The Water Reservoir can be filled in two ways.

Your Brewer is able to produce hot water for making hot cocoa from a packet, for use in cooking, for making soups, etc. Simply follow the instructions on page 7 — “Ready To Brew Your First Cup” without adding a K-Cup®pack.

NOTE: After brewing a hot cocoa K-Cup®pack, we recommend running a cleansing brew without a K-Cup®pack.

Purging the Brewer

Small Mug

(7.25 oz.)

Large Mug

(9.25 oz.)

disabled to prevent accidental activation.

Re-activate the Brew Buttons by raising and

lowering the Handle completely.

8. The LCD Control Center will indicate

“BREWING” and the cup size you selected

will illuminate. CAUTION: There is extremely

hot water in the K-Cup®Pack Holder during the

brew process. To avoid risk of injury, do not lift

the Handle or open the K-Cup®Pack Assembly

Housing during the brew process.

9. There may be a short pause prior to coffee

being dispensed. The entire brew process

lasts for approximately 1 minute and ends

with a burst of air to remove all liquid from

the K-Cup®pack.

fill in preparation for the next brew. The pump will make a vibrating sound. This is normal.

Stopping the Brew Process

If you need to stop brewing after the process has started, press the Power Button to turn the Brewer off. The flow of coffee, tea or hot cocoa will stop, the heating element will shut off, and the blue lights illuminating the brew buttons and Water Reservoir will disappear. NOTE: You may get less coffee, tea or hot cocoa in your cup during your next brew. We recommend that you perform a cleansing brew after a terminated brew. Then your NEXT brew will be the volume you have selected.

8

1. Lift off the Water Reservoir Lid and pour water directly into the Water Reservoir while it is still attached to the Brewer, then replace the Lid.

2.Remove the Water Reservoir from Brewer by first removing Lid from the Water Reservoir, then lifting the Water Reservoir straight up and away from Brewer. Fill with water. Place the Water Reservoir back on the Brewer and replace the Lid. IMPORTANT: Do not remove the Water Reservoir during the brewing process.

Brewing Iced Beverages

Your iced tea and iced coffee taste best when fresh-brewed hot over ice. Try it by placing a tall cup filled with ice on the Drip Tray Plate (the Drip Tray Assembly can be removed to accommodate taller cups), choose your favorite K-Cup®pack and press your preferred cup size. Also, look for the Brew Over Ice™ icon on K-Cup®packs that are specially crafted to brew over ice! IMPORTANT: Do not brew into a cup made of glass. Doing so may cause the glass to crack or break.

If your Brewer has not been used for more than one week, you should purge the water from the inner tank.

1.If there is water in the Water Reservoir, remove the Lid, then lift the Water Reservoir straight up and away from Brewer. Discard water, rinse and refill with water. Place the Water Reservoir back on the Brewer and replace the Lid. (If there is no water in the Water Reservoir, simply refill.)

2.Be sure the Brewer is turned on. Raise and lower the Handle on the Brewer without inserting a K-Cup®pack.

3.The LCD Control Center will indicate “READY TO BREW” and the Small Cup, Small Mug and Large Mug Buttons will flash. Be sure to have a large mug on the Drip Tray Plate and then press the Large Mug Button.

4.Repeat steps 2 and 3 one more time to completely purge water from inner tank.

If you are experiencing any problems with your Brewer, please contact Customer Service at 1.866.901.BREW (2739).

9