TROUBLESHOOTING

If your amplifi er does not appear to be working, check the obvious things fi rst such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is a Protection (PRT) LED on the side panel of your KICKER KX series amplifi er. Depending on the state of the amplifi er and the vehicle’s charging system, the LED will either glow red or be off.

Red (PRT) LED flickering with loud music? The red (PRT) LED indicates low battery voltage or an illegal load. Check all the connections in your vehicle’s charging system. It may be necessary to replace or charge your vehicle’s battery or replace your vehicle’s alternator.

Red (PRT) LED on, no output? Amplifi er is very hot = thermal protection is engaged. Test for proper impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance and multiple speaker wiring suggestions). Also check for adequate airfl ow around the amplifi er. Amplifi er shuts down only while vehicle is running = voltage protection circuitry is engaged. Voltage to the amplifi er is not within the 10–16 volt operating range. Have the vehicle’s charging and electrical system inspected. Amplifi er will only play at low volume levels = short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle chassis. Check for damaged speakers or speaker(s) operating below the minimum recommended impedance.

No or low output? Check the balance control on source unit Check the RCA (or speaker input) and speaker output connections.

Alternator noise-whining sound with engine’s RPM? Check for damaged RCA (or speaker input) cable Check the routing of RCA (or speaker input) cable Check the source unit for proper grounding Check the gain settings and turn them down if they are set too high.

Reduced bass response? Reverse a speaker connection from positive to negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was out of phase.

Ground Noise? KICKER amplifi ers are engineered to be fully compatible with all manufacturers’ head units. Some head units may require additional grounding to prevent noise from entering the audio signal. If you are experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the head unit to the chassis will remedy this issue.

CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can result in blown amplifi er fuses as well as the failure of other critical systems in the vehicle.

If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the KICKER homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab, choose the subject you are interested in, and then download or view the corresponding information. Please E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or specifi c questions.

2013 KX 4-Channel Amps Rev C.indd 7

7

10/24/2012 4:31:57 PM

Page 6 Page 8
Page 7
Image 7
Kicker KX400.4 owner manual Troubleshooting
Page 6 Page 8

KX400.4 specifications

The Kicker KX400.4 is part of Kicker's renowned lineup of amplifiers, designed to deliver powerful and crystal-clear audio performance for car enthusiasts and audiophiles alike. This four-channel amplifier is engineered to provide incredible sound quality while maintaining efficiency and durability, making it a perfect choice for powering a complete audio system.

Among its main features, the KX400.4 boasts an impressive 400-watt output, ensuring that it can handle even the most demanding speaker setups. With a maximum power rating of 100 watts per channel at 4 ohms and 200 watts per channel at 2 ohms, it can drive a wide range of speaker configurations for optimal audio performance. The amplifier also features a flexible crossover system, allowing users to customize frequency ranges for each channel. This enables seamless integration of various components, ensuring that subwoofers, mids, and highs all work together harmoniously.

One of the standout technologies in the KX400.4 is its advanced thermal management system, which helps prevent overheating during extended use. The amplifier utilizes a full-range Class D circuit design, promoting high efficiency while minimizing heat generation. This not only extends the lifespan of the unit but also allows for a compact design that can be easily installed in various vehicles, even those with limited space.

The KX400.4 incorporates a variable bass boost feature, giving users the ability to enhance low-frequency response according to personal preferences. This allows for a customizable listening experience, providing the flexibility to adjust the bass levels on-the-fly. Additionally, the amplifier is equipped with a signal sensing input, simplifying installation by enabling automatic turn-on when a signal is detected.

Moreover, the KX400.4 is built with high-quality components, including a robust aluminum chassis that offers both durability and aesthetic appeal. The amplifier's design features top-quality RCA inputs and speaker outputs, ensuring secure connections for optimal performance.

In summary, the Kicker KX400.4 sets a high standard in car audio amplification, combining power, efficiency, and a range of user-friendly features. Its advanced technologies and solid construction make it an excellent choice for anyone looking to elevate their in-car listening experience. With this amplifier, Kicker continues to demonstrate its commitment to delivering exceptional automotive audio solutions for enthusiasts around the world.
Top Page Image Contents