2007 WX
2.Wiring Before wiring the Warhorse amplifier, disconnect the vehicle’s batteries to avoid an electrical short. Eight (8) identical,
Caution The Kicker WX amplifier outputs extremely high voltage signals from the voice coil (speaker) outputs and can cause serious injury or death from electrocution. It is imperative to read the manual carefully and follow all of the recommended safety precautions before installing the WX amplifier.
ModelWX10000.1 Fuse Three (3) x 250 Ampere PowerGroundWire Three (3) x 1/0 Gauge
From two (2) of the batteries in the battery network, connect 1/0 gauge ground wire from the negative terminals of the batteries to a
Figure 4
Warning: This amplifier is not like anything you have ever hooked up before. Pay close attention to the wiring diagrams in this manual. Improper connections will damage the amplifier.
With the control panel shield removed, connect a twisted pair of RCA
The Warhorse amplifier requires at least two (2)
Eight (8) identical, high- quality,
Without adequate
charging capability, the WX amplifier can draw enough current to shut down your vehicle’s computer system. This may adversely affect your ability to control your vehicle.
(45cm) 18" or less
250 ampere
fuse
(45cm)
+12V
+12V
+12V
+12V
|
| 250 ampere |
|
|
|
| fuse |
|
|
|
|
|
| |
18" | oOr lessL |
| (45cm) 18" | oOr lessL |
| ||||
|
|
|
|
|
+12V
+12V
+12V
+12V
ANL fuse holder |
|
|
|
|
|
|
|
|
|
|
|
|
| |
contains three (3) 250 |
|
|
|
|
|
|
| |||||||
ampere fuses. The fuse |
|
|
|
|
|
|
| |||||||
holder should be |
|
|
|
|
|
|
|
|
|
|
|
|
| |
installed within 18” of |
|
|
|
|
|
|
| |||||||
battery network. |
|
|
|
|
| 250 ampere |
|
|
|
|
|
| 250 ampere | |
|
|
|
|
|
|
|
|
|
|
| ||||
(45cm) |
|
| or less |
| fuse | (45cm) |
| or less |
| fuse | ||||
18" |
|
| 18" |
|
| |||||||||
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
At least two (2)
CONFIGURATION
The three (3) positive 1/0 gauge power wires should be the last wires connected in the installation. Install a Kicker three (3) gang ANL fuse holder (not incuded) within 18” (45cm) of the battery network and
Figure 3
Power Hood
Wire Guide
Run two (2) ground wires from separate negative battery terminals. Ground wires should connect to vehicle chassis within 18” of each other.
Mount Amplifier within 48” | + |
| |
(122cm) of Battery Network |
|
-
Improper connections will damage the amplifier and/or cause serious injury or death. Be sure that all wiring is connected to the appropriate polarity.
INSTALLATION
If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab, choose the product or subject you are interested in, and then view the corresponding information. Please
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring. All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.
Positive Power | Negative Power |
Connector | Connector |
The WX amplifier outputs dangerous voltage levels from the voice coil (speaker) outputs and can cause serious injury or death from electrocution. Never contact the voice coil outputs, connect speakers, or contact speaker wires while the amplifier is turned on.
| Strip Wire |
|
Figure 5 | 9/16” (14mm) | AndersonTM Connector |
|
| |
8 Gauge Speaker Wire |
|
|
Secure wire to metal | Metal Contacts |
|
contacts by soldering. |
|
|
3. Configuration The following diagram shows the recommended mono configuration for your Kicker WX amplifier. The WX amplifier can only drive extremely
4 | WX10000.1AMPLIFIER | 5 |