5.Do not remove film or cover.

6.Reassemble the trim and top grille after the dolly has been removed from the refrigerator.

Install Anti-Tip Boards

IMPORTANT:

To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

It is recommended that board(s) be installed before the refrigerator is installed.

Board(s) must be long enough to fully cover the width of the compressor cover.

Locate the board(s) so the bottom surface(s) of the board(s) is(are) 84" (213 cm) from the floor.

During installation, raise the refrigerator up so there is ¹⁄₄" (6.35 mm) maximum between the top of the refrigerator and the bottom of the anti-tip board(s). Do not crush the compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1.Mark the stud locations on rear wall 80" to 90" (203 cm to 229 cm) above floor.

2.Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards to wall studs behind refrigerator. Use six #8 x 3" (7.6 cm) (or longer) wood screws. The wood screws must be screwed into the studs at least 1½" (3.8 cm). The board(s) must overlap the compressor cover.

A B

C

2" (5 cm)

D

A. Center board ¹⁄₄" (6.35 mm) max. above refrigerator

B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

Connect the Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

Style 1 - Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1, see “Style 2 - Copper Line Connection.”

1.Unplug refrigerator or disconnect power supply.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

2.Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3.Remove the short, black plastic tube from the end of the water line inlet. This tube protects the fitting during shipping only.

4.Thread the provided nut onto the shutoff valve as shown.

A

B

C

A.Bulb

B.Nut

C.Water tubing

5.Turn shutoff valve ON.

6.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

7.Plug in the refrigerator or reconnect power.

8.Flush the water system. See “Water System Preparation.”

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

Style 2 - Copper Line Connection

Connecting to Water Line

NOTE: If existing water line meets the “Water System Requirements,” see “Connecting to Refrigerator.”

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

Make sure it is a cold water pipe.

Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4.Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a cordless drill, drill a ¹⁄₄" (6.35 mm) hole in the cold water pipe you have selected.

 

A

G

B

 

 

C

F E

D

A. Cold water pipe

E. Compression sleeve

B. Pipe clamp

F. Shutoff valve

C. Copper tubing

G. Packing nut

D. Compression nut

 

20

Page 20
Image 20
KitchenAid 2316565C manual Install Anti-Tip Boards, Connect the Water Supply, To Install Anti-tip Boards

2316565C specifications

The KitchenAid 2316565C is a versatile and innovative blending tool designed for culinary enthusiasts who appreciate both quality and performance in their kitchen appliances. This model stands out due to its powerful motor and unique features that enhance the cooking experience.

One of the main features of the KitchenAid 2316565C is its robust 3.5 horsepower motor, which ensures efficient blending even with the toughest ingredients. Whether you're making smoothies, soups, or sauces, this blender can effortlessly handle ice and frozen fruits, delivering a smooth and consistent texture every time.

The unit's stainless-steel blades are engineered for durability and precision. Their unique design helps to create a vortex that pulls ingredients down toward the blades for even blending. This technology allows for superior blending performance, reducing the preparation time for various recipes.

The KitchenAid 2316565C also comes with a large capacity blending jar that accommodates up to 64 ounces. This generous size is perfect for family meals or entertaining guests, enabling you to blend large batches without needing to refill. Additionally, the jar features measurement markings, allowing for precise ingredient additions and recipe adjustments on the fly.

Another key feature of this blender is its intuitive control panel, which includes multiple speed settings and a pulse function. Users can easily customize blending speeds to achieve the desired consistency, whether it’s a silky smooth puree or a chunky salsa. The pulse function adds versatility, making it simple to chop or mix ingredients without over-blending.

Safety is a priority with the KitchenAid 2316565C. The blender includes a safety lock mechanism that prevents operation unless the lid is securely in place. This feature provides peace of mind, especially when blending hot ingredients, ensuring that spills and splatters are minimized.

Finally, the appliance's sleek and modern design seamlessly fits into any kitchen decor, while its easy-to-clean removable parts make it a practical choice for daily use. The blender is dishwasher-safe, allowing for hassle-free clean-up after meal prep.

In summary, the KitchenAid 2316565C is a powerful and efficient blender that combines performance, safety, and style. It is ideal for users seeking to elevate their culinary creations with ease, making it a worthy addition to any kitchen.