Electrical requirements

Electrical Shock Hazard

l Electrical ground is required on this appliance.

lDo Not ground to a gas pipe.

l Do Not have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in an electrical shock.

l Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded.

Failure to follow these instructions could result in serious injury or death.

If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path is adequate.

IMPORTANT:

Save Installation Instructions for the local electrical inspector’s use.

This appliance must be connected to the proper electrical voltage and

frequency as specified on the serial/rating plate located behind the oven door (double oven models - upper oven) on the front frame. A fuse is required in both sides of the line. A time-delay fuse is recommended. Use the voltage and kilowatt rating given on the serial/rating plate to select the proper fuse size from the chart.

Electrical connection

Electrical Shock Hazard

l Electrical ground is required on this appliance.

l Do Not connect to the electrical supply until appliance is permanently grounded.

l Disconnect power to the junction box before making the electrical connection.

l This appliance must be connected to a grounded, metallic, permanent wiring system, or a grounding connector should be connected to the grounding terminal or wire lead on the appliance.

Failure to do so could result in a fire, personal injury or electrical shock.

This appliance is manufactured with white (neutral) power supply wire and a cabinet- connected green grounding wire twisted together.

Connect the appliance cable to the junction box through the U.L.-listed conduit connector. Complete electrical connection according to local codes and ordinances.

A. Where local codes permit...

connecting the cabinet-grounding conductor to the neutral (white) junction box wire:

Cable from

C. If connecting to a four-

wire electrical system...

Do Not connect the cabinet-grounding conductor to the neutral (white) junction box

iom

White

wlree

conduit

Figure 3

connector

1.Disconnect the power supply.

2.Separate the green (or bare) and white appliance cable wires.

3.Connect the white appliance cable wire to the neutral (white) wire in the junction box.

4.Connect the two black wires together; then the two red wires together. See Figure 3.

5.Connect the green appliance cable wire to the green grounding wire in the junction box.

Now start...

with oven in kitchen.

Remove shipping materials, tape, and protective film from oven. Do Not

remove’shipping base at this time.

121Remove the racks and other parts

. from inside the oven.

Fuse Requirements:

120/208

6.2

30

a

6

6

 

Figure 1

 

conduit

 

6.2 to 8x3

40

a

6

4

 

Cable

connector

 

 

 

 

 

 

 

 

from

oven

[I

 

 

 

 

 

 

l.Di;nnect~~~~~

 

. _ ,- .

 

 

 

 

 

 

 

2. Remove the terminal block cover.

1

 

 

 

 

 

1

3. Connect together 3 wires: green and white

your local

 

 

 

 

appliance cable wires and the neutral (whrte)

+ Check

codes

and

ordinances.

 

 

 

 

wire in junction

box.

 

 

 

 

 

 

 

 

 

4. Connect the two black wires together; then the two red wires together. See Figure 1.

l Use both hands to remove oven doors. l Grasp only the sides of oven doors.

l Do Not use handle or any portion of the trim for lifting.

l Because of the weight and size of the single or double oven, two or more people are needed to move and safely install the oven.

Failure to properly grasp the oven doors or to lift ovens properly could result in damage to the product or personal injury.

OVEN MUST BE CONNECTED WITH

IBI n SOLID COPPER WIRE ONLY.

Wire sizes and connections must El . conform to the requirements of the National Electrical Code, ANSI/NFPA 70 - latest edition** and all local codes and ordinances. Wires sizes and connections must conform with the rating of the appliance.

Copies of the standards listed may be obtained from:

B. Where local codes Do Not

permit...

connecting the cabinet-grounding conductor to the neutral (white) junction box wire:

Cable from

“National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

This appliance should be connected IDI . directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with

Figure 2

Cable conduit from oven connector

Selfcleaning ovens: Insert a nail (or equivalent, 5/32” diameter item) into the hole in each of the hinges. Close the door as far as possible. Lift the oven door off of the hinges. Set aside.

Non-self cleaning ovens: Open the oven door

grounding wire). The flexible armored cable from the appliance should be connected directly to the junction box.

E-ILocate the junction box to allow as

. much slack in the cable as possible between the junction box and the appliance so that the oven can be moved if servicing is ever necessary. Do Not cut the conduit.

El A U.L.-listed conduit connector must

. be provided at the junction box.

IGIA wiring diagram is included in the n Tech Sheet. The Tech Sheet is

located behind the air grille.

Ungrounded Neutral

1.Disconnect power supply.

2.Separate the green and white appliance cable wires.

3.Connect the white appliance cable wire to the neutral (white) wire in the junction box.

4.Connect the two black wires together; then the two red wires together. See Figure 2.

5.Connect the green or bare grounding wire from the appliance cable to a grounded wire in the junction box.

to the broil “stop”position and lift the door upwards to remove. Set oven door aside.

Property Damage

Before moving oven across floor, check that oven is on shipping base or slide single or double oven onto cardboard or hardboard.

Failure to follow these instructions may result in damage to floor covering.

141Turn power supply off. Move oven close

. to final position. Remove and discard shipping base. Feed appliance cable through the opening in cabinet. Make electrical connection. See “Electrical requirements” and “Electrical connection” sections, Panel B.

Panel B

Page 3
Image 3
KitchenAid 3182137 installation instructions Now start, With oven in kitchen, Fuse Requirements, Panel B

3182137 specifications

The KitchenAid 3182137 is a standout kitchen appliance that embodies versatility and efficiency, making it an essential tool for both amateur cooks and culinary professionals. This mixer is a part of KitchenAid's renowned line of products known for their durability, style, and innovative design.

One of the principal features of the KitchenAid 3182137 is its powerful motor. With a robust capacity, it allows users to handle heavy doughs and thick batters effortlessly. This ensures that no recipe is beyond reach, whether you are kneading bread dough or whipping cream. The mixer comes equipped with multiple speed settings, providing the flexibility to tailor the mixing speed to the specific requirements of the task at hand. From slow stirring to high-speed whipping, you can achieve the perfect consistency every time.

Another significant aspect of the KitchenAid 3182137 is its tilt-head design, which offers easy access to the mixing bowl. This feature allows for hassle-free bowl removal and the addition of ingredients while the mixer is in operation. The generous capacity of the bowl ensures that you can prepare large batches, making it ideal for family gatherings or meal prepping.

The KitchenAid 3182137 also emphasizes user-friendliness with its intuitive controls. The easy-to-read speed settings and the ergonomic handle enhance the overall blending experience. Clean-up is simplified, as the bowl and attachments are dishwasher-safe, saving you time and effort.

In terms of build quality, the KitchenAid 3182137 does not disappoint. Made from durable materials, it is designed to withstand everyday use while maintaining its aesthetic appeal. The classic design and various color options allow it to seamlessly integrate into any kitchen decor.

Moreover, this mixer features a versatile attachment hub that expands its functionality. You can easily add attachments for pasta making, food grinding, and slicing, transforming the mixer into a multi-functional kitchen tool.

In summary, the KitchenAid 3182137 is characterized by its powerful motor, multiple speed settings, user-friendly design, and versatility. Whether you are a novice in the kitchen or an experienced chef, this mixer is sure to elevate your cooking and baking experiences. With its combination of style, strength, and functionality, it stands as a true must-have for any kitchen enthusiast.