Tools needed for installation, Panel B | KitchenAid 9751596 specs

Tools needed for installation:

flat-blade screwdriver or-5116” (0.8 cm) nut

hand or electric drill wood floor: l/8” (0.3 cm) drill bit

concrete/ceramic floor: 3/16” (0.48 cm) carbide- tipped masonry drill bit

Parts supplied for installation:

Power supply cord

Use a new 40-amp power supply cord.

Local codes may permit the use of a U.L.-listed, 250~volt, 40-ampere range power supply cord (pigtail). Power supply cord should be Type SRD or SRDT and be at least four feet long. The wires that connect to the range must end with ring terminals. A 3/4” (1.9 cm), U.L.-listed strain relief must be installed where the power supply cord connects to the range. (See Figures 1 and 2.)

ring terminals

This blade connected to this conduc

strain relief

(white or center)

Three-wire power supply cord

NEMA lo-50P

	Figure	1
314”	1.9 cm)
U.L.- Iisted		NEUTRAL
strain	relief \.	(white)

grounding prong

Electrical connections

NOTE: The metal chassis of the range MUST be earth-grounded in order for the control panel to work. If the metal chassis of the range is not earth- grounded, NO keypads will operate. Check with a qualified electrician if you are in doubt as to whether the metal chassis of range is earth-grounded.

Where local codes permit connecting the frame-grounding conductor to the neutral (white) junction box wire:

This appliance is manufactured with the neutral terminal connected to the cabinet. If local codes Do Not permit connecting cabinet-grounding conductor to neutral wire, use “Four-wire connection” instructions.

Electrical Shock/Fire Hazard

Check that wiring you are using matches colors shown in illustrations and specified in instruction steps. If wiring does Not match, it is your responsibility to have a qualified electrician install correct wiring.

Failure to follow these instructions could result in fire, electrical shock or death.

(Bracket must be securely mounted to sub- floor. Thickness of flooring may require longer screws to anchor the bracket to sub-floor.)

Electrical requirements

Save Installation Instructions for the local electrical inspector’s use.

Power supply cord is not provided and is available through your local electrical supply houses.

Electrical Shock Hazard

l Electrical ground is required on this appliance.

. Use only a new power supply cord kit ratec at 250 volts, 40 amperes and investigated for use with ranges. Do Not reuse an old power supply cord.

l Do Not modify the power supply cord plug If it does not fit the outlet, have a proper outlet installed by a qualified electrician.

l Do Not use an extension cord with this appliance.

lDo Not ground to a gas pipe.

lDo Not have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in an electrical shock.

l Check with a qualified electrician if you arc in doubt as to whether the appliance is properly grounded.

Failure to follow these instructions could result in serious injury or death.

If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path is adequate.

A three-wire or four-wire, single-phase, 120/240- volt, 60-Hz, AC-only, electrical supply (or three- wire or four-wire 120/208-volt if specified on the serial/rating plate) is required on a separate

40-ampere circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended.

THE RANGE MUST BE CONNECTED WITH COPPER WIRE ONLY.

Wire sizes (COPPER WIRE ONLY) and connections must conform with the rating of the appliance (40 amperes).

A wiring diagram is located on back of range.

Panel B

Four-wire power supply cord (Mobile home or other four-wire installations)

NEMA lo-5OP Figure 2

The power supply cord must have three No.-10 copper wires to match a three-wire receptacle of NEMA Type 1O-50R. (See Figure 3.)

For mobile home or other four-wire installations: This appliance is manufactured with ground connected to cabinet. The ground must be revised so the green grounding wire of the four- wire power cord is connected to the cabinet. See four-wire electrical connection section, Panels C and D.

When a four-wire receptacle of NEMA Type 14-50R is used (See Figure 4.), a matching U.L.-listed, four-wire, 250~volt, 40-ampere, range power supply cord (pigtail) must be used. This cord contains four copper conductors with ring terminals on the appliance end, terminating in a NEMA Type 14-50P plug on the supply end. The fourth (grounding) conductor must be identified by a green or green/yellow cover and the neutral conductor by a white cover. Cord should be Type SRD or SRDT with a U.L.-listed strain relief and be at least four feet long.

The MINIMUM conductor sizes for the copper

4-wire power supply cord are:

40-ampere circuit 2, No.-8 conductors

1, No.-1 0 white neutral 1, No.-8 green grounding

For	use	where		P 1
local	codes			UG
ermit		use of		UG
Plexible		power		ny$l
supply		cord.		ny$l
		three-wire	wall	wire	wall
		three-wire	wall	four3-
		receptacle		receptacle
		(16SOR)		(14~SOR)
		Figure	3	Figure	4

Direct wire

The range can be connected directly to fused disconnect or circuit breaker box through flexible, armored or non-metallic sheathed, copper cable (with grounding wire). Do Not use two-wire with bare grounding wire. All current-carrying wires must be insulated.

A U.L.-listed conduit connector must be provided at each end of the power supply cord (at the appliance and at the junction box). USE ONLY lo-GAUGE SOLID COPPER WIRE. DO NOT USE ALUMINUM. Allow two or three feet of slack in the line so the range can be moved if servicing is ever necessary.

Figure 5

cover

2. Remove the terminal block cover located on back of range. Remove the 3/8” (0.95 cm) brass terminal nuts attached to the knockout.

3. Remove the knockout for the 40-ampere power supply cord.

silver-colored	\\\\\\	1
	’ ’

n	U.L.-listed	’
Figure	strain relief	i
Figure	7

Attach a 314” (1.9 cm) U.L.-listed strain on strain relief) to the rain relief firmly to cabinet.

Place power supply cord through strain relief.

Using the 3/8” (0.95 cm) brass nuts,

ch the neutral (white) wire of power supply to the center, silver-colored screw of the

her two wires to the outer rews. (See Figure 7.)

e factory-installed nuts on

g nuts are installed tight.

6. Tighten strain relief screws

.:::-..-..: Iv ::.:::.

..-.-.-.-. . Reattach terminal block cover.

9751596 specifications

The KitchenAid 9751596 is a versatile and powerful stand mixer designed to elevate your culinary experience. Known for its robust build and innovative features, this appliance is a favorite among both amateur and professional chefs. With a strong emphasis on performance, durability, and style, the KitchenAid 9751596 stands out in the crowded kitchen appliance market.

One of the standout characteristics of the KitchenAid 9751596 is its powerful motor. Equipped with a high-efficiency motor, it effortlessly handles heavy mixtures, from bread dough to thick batters. This makes it an excellent choice for anyone who enjoys baking, as it can mix, knead, and whip with ease. The direct-drive transmission ensures that power is efficiently transferred to the mixing bowl, which enhances its performance while reducing wear and tear.

The 9751596 features multiple speed settings, allowing users to select the optimal speed for various tasks. With a total of ten speeds, you can achieve everything from a gentle stir to a vigorous whip, giving you complete control over your mixing process. The inclusion of a power hub expands its versatility even further, enabling you to attach a range of optional accessories. These can include pasta makers, food grinders, and vegetable spiralizers, making this mixer a multifunctional kitchen companion.

The design of the KitchenAid 9751596 is both functional and aesthetically pleasing. Its iconic, retro-style design is available in a variety of colors, allowing it to seamlessly blend into any kitchen décor. The stainless steel bowl is not only durable and easy to clean but also has a capacity that can cater to large batches, making it perfect for family gatherings or entertaining.

Another notable feature is the tilt-head design, which allows easy access to the bowl and beaters. This design simplifies the process of adding ingredients and cleaning, providing convenience for everyday use. The included accessories, such as the flat beater, dough hook, and wire whip, are crafted for efficiency and effectiveness, ensuring that you achieve the desired consistency with minimal effort.

In summary, the KitchenAid 9751596 stand mixer combines power, versatility, and elegance. With its strong motor, multiple speed settings, and the ability to add various attachments, it provides unmatched functionality. The tilt-head mechanism and stylish design further enhance its appeal, making it an essential tool for any kitchen enthusiast. Whether you're baking bread, whipping cream, or making homemade pasta, the KitchenAid 9751596 is designed to help you achieve your culinary aspirations with ease.

KitchenAid 9751596 Tools needed for installation, Parts supplied for installation, Panel B

Models: 9751596