KitchenAid KDRS505X dimensions 30 76.2 cm Double Oven Dual Fuel Range, Type of Gas

	30" (76.2 cm) Double Oven Dual Fuel Range
PRODUCT MODEL NUMBERS	PRODUCT DIMENSIONS
KDRS505X	B*
GAS SUPPLY REQUIREMENTS

Type of Gas

Natural gas:

This range is design-certified by CSA International for use with

Natural gas or, after proper conversion, for use with LP gas.

● This range is factory set for use with Natural gas. See “Gas
Conversions” section. The model/serial rating plate located
behind the control panel has information on the types of gas	C**
that can be used. If the types of gas listed do not include the
type of gas available, check with the local gas supplier.
LP gas conversion:
Conversion must be done by a qualified service technician.	A
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different
gas without consulting the serving gas supplier. See “Gas	D
Conversions” section.

Gas Supply Line

●Provide a gas supply line of ³⁄₄" (1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in

	insufficient gas supply. With LP gas, piping or tubing size can						E***
	be ¹⁄₂" (1.3 cm) minimum. Usually, LP gas suppliers determine					F
	the size and materials used in the system.
	NOTE: Pipe-joint compounds that resist the action of LP gas
	must be used. Do not use TEFLON®† tape.
Flexible metal appliance connector:					A. 35³⁄₄" ± ¹⁄₈" (90.8 ± 0.3 cm)		C. 47¹⁄₈" ± ¹⁄₈" (119.7 ±	0.3 cm)
● If local codes permit, a new CSA design-certified, 4 to 5 ft (122					cooktop height (minimum)		overall height (minimum) with
					with leveling legs screwed all		leveling legs screwed all the
	to 152.4 cm) long, ¹⁄₂" (1.3 cm) or ³⁄₄" (1.9 cm) I.D., flexible				the way in		way in**
	metal appliance connector may be used for connecting range to				B. Model/serial/rating plates		D. 28¹⁄₂" ± ¹⁄₄" (72.4 ±	0.6 cm)
	the gas supply line.				(located behind the control		depth with handle
					panel)*		E. 26¹⁄₈" ± ¹⁄₈" (66.4 ±	0.3 cm)
							F. 29¹⁵⁄₁₆" ± ¹⁄₁₆" (76.0 ±		0.2 cm)
							width
● A ¹⁄₂" (1.3 cm) male pipe thread is needed for connection to the					*** Model/serial/rating plates may be rotated up from behind the control
	female pipe threads of the inlet to the appliance pressure				panel for viewing from the front of the range.
	regulator.				*** Range can be raised approximately 1" (2.5 cm) by adjusting the leveling
● Do not kink or damage the flexible metal tubing when moving					legs.
	the range.				*** Excludes handle. Dimension given is from wall to front of oven door and
Rigid pipe connection:					will vary based on electric outlet receptacle installation.
The rigid pipe connection requires a combination of pipe fittings					ELECTRICAL REQUIREMENTS
to obtain an in-line connection to the range. The rigid pipe must
be level with the range connection. All strains must be removed					To properly install your range, you must determine the type of electrical connection
from the supply and fuel lines so range will be level and in line.					you will be using and follow the instructions provided for it here.
					● Range must be connected to the proper electrical voltage and frequency as
					specified on the model/serial number rating plate. The model/serial number rating
					plate is located behind the control panel. Refer to the figures in “Product
					Dimensions” in the “Location Requirements” section.
					● This range is manufactured with the neutral terminal connected to the cabinet.
● Must include a shutoff valve:					Use a 3-wire, UL listed, 40- or 50-amp power supply cord (pigtail) (see following
	The supply line must be equipped with a manual shutoff valve.				Range Rating chart). If local codes do not permit ground through the neutral, use
					a 4-wire power supply cord rated at 250 volts, 40 or 50 amps and investigated for
	This valve should be located in the same room but external to
					use with ranges.
	the range opening, such as an adjacent cabinet. It should be in a
	location that allows ease of opening and closing. Do not block				Range Rating*		Specified Rating of Power Supply
	access to shutoff valve. The valve is for turning on or shutting
							Cord Kit and Circuit Protection
	off gas to the range.
		B			120/240 Volts	120/208 Volts	Amps
					8.8 - 16.5 KW	7.8 - 12.5 KW	40 or 50**
A			A. Gas supply line		16.6 - 22.5 KW	12.6 - 18.5 KW	50
			B. Shutoff valve “open”		** The NEC calculated load is less than the total connected load listed on the
				position
			C. To range		model/serial rating plate.
			C		** If connecting to a 50-amp circuit, use a 50-amp rated cord with kit. For 50-amp
†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.					rated cord kits, use kits that specify use with a nominal 1³⁄₈" (34.9 mm) diameter
					connection opening.				Page 1 of 2
Because Whirlpool Corporation policy includes a continuous commitment to improve					Dimensions are for planning purposes only. For complete details, see Installation				Ref. W10345640B
our products, we reserve the right to change materials and specifications without notice.					Instructions packed with product. Specifications subject to change without notice.				1/28/11