Installing the Tank

1.Position tank vertically beneath faucet so that the longer copper tube from the faucet reaches the easy-connect fitting on top of the tank.

2.Use a pencil to mark on the wall where the top of tank needs to be located. Set tank aside. Mark a second line 2-1/4"

(5.7 cm) below the first line.

IMPORTANT: The tank must be positioned so that the copper tubing and flexible tubing from the faucet does not kink.

3.Position mounting bracket on wall so that bottom of mounting bracket is even with the lower line.

4.Use two screws (and plastic anchors if attaching to dry wall) to fasten mounting bracket to wall. Hang tank on bracket.

2-1/4"

(5.7 cm)

off position

mounting

bracket

6.Connect the flexible tube from the faucet to the center tank tube. Make sure the flexible tube does not kink. To avoid kinking, the tube may be shortened.

The center tank tube is not an easy-connect fitting. To connect the flexible tube, use pliers and open the supplied hose clamp. Slide the clamp onto the flexible tube about 2" (5 cm) from the tube end.

flexible tube

hose clamp

tank tube

7.Push the flexible tube down onto the tank tube as far as it will go. Position the hose clamp so that it is close to the end of flexible tube.

hose clamp

IMPORTANT: Do not plug power supply cord into outlet at this time.

5.IMPORTANT: Do not lengthen, twist or tightly bend tubing. Do not use any sealing compounds.

Connect the longest 1/4" copper faucet tube to the rear easy- connect fitting on top of tank. Push tubing straight into fitting as far as it will go. Pull on tubing. The tubing should not come out when properly installed.

copper

 

faucet tube

collet

 

easy-connect fitting

NOTE: If you need to remove tubing, push down on collet. Pull tubing out of easy-connect fitting. It is easier to push the collet down if a 1/4" or 7 mm open-end wrench is used as shown.

copper

1/4" or 7 mm

faucet tube

open-end

 

wrench

collet

 

8.Install saddle valve kit or other plumbing parts as needed to connect 1/4" tubing from faucet easy-connect fitting to cold water supply line.

9.Flush line into bucket or pan to remove any debris that may have been trapped in supply line during plumbing connection.

10.Check that water flows freely and that there are no leaks.

11.Connect 1/4" water supply line tubing to faucet copper tubing with the factory-assembled easy-connect fitting. Push water supply line tubing straight into fitting as far as it will go. Pull on tubing. The tubing should not come out when properly installed.

factory assembled easy-connect fitting

NOTE: If you need to remove tubing, push down on collet and pull tubing out of easy-connect fitting.

IMPORTANT: For proper operation, do not remove the factory-assembled easy-connect fitting from tube.

12.Open water line to faucet.

5

Page 4 Page 6
Page 5
Image 5
KitchenAid KHWC160, KHWG160, KHWL160 installation instructions Installing the Tank, Cm below the first line
Page 4 Page 6

KHWC160, KHWL160, KHWG160 specifications

The KitchenAid KHWG160, KHWL160, and KHWC160 represent an impressive line of kitchen appliances designed to enhance culinary experiences for both amateur cooks and professional chefs alike. Each model showcases KitchenAid's commitment to quality, innovation, and style.

The KHWG160 is a powerful stand mixer known for its robust performance and versatile capabilities. Equipped with a 300-watt motor, this mixer offers ten speeds, allowing users to tackle a variety of tasks—from mixing batter to kneading dough with ease. One standout feature of the KHWG160 is its unique planetary mixing action, which ensures that ingredients are mixed thoroughly and evenly by moving in multiple directions. This results in a consistent mixture every time, significantly reducing prep time and enhancing the quality of baked goods.

In contrast, the KHWL160 is a sleek blender that combines cutting-edge technology with an elegant design. It boasts a high-performance motor that provides up to 15 blending speeds, allowing for precision control when creating smoothies, soups, or sauces. This model is also equipped with a unique ice-crushing feature that can handle frozen ingredients effortlessly, making it ideal for tropical drinks or frozen desserts. Additionally, the KHWL160's stainless steel blades are designed for durability and efficiency, ensuring that they stay sharp and effective over time.

Finally, the KHWC160 is an innovative food processor that streamlines meal prep with its multifunctional design. With a 750-watt motor and multiple attachments, this food processor can slice, shred, chop, and puree ingredients to suit any recipe. The large capacity bowl allows for handling larger quantities of food, making it a fantastic addition for families or those who love to entertain. The KHWC160 also includes a safety lock mechanism, ensuring that the appliance operates safely during use.

All three models are a testament to KitchenAid's dedication to blending functionality with aesthetic appeal. They feature a classic design that complements any kitchen décor while being built from high-quality materials that ensure durability. With their powerful motors, innovative features, and user-friendly interfaces, the KitchenAid KHWG160, KHWL160, and KHWC160 are perfect companions for elevating your culinary skills and delivering delicious results every time.
Top Page Image Contents