Manuals / KitchenAid / Kitchen Appliance / Dishwasher

KitchenAid KUD01, KAD-7 Introduction, Goals And Objectives, To The Instructor/Independent Student

Models: KUD01 KAD-7

1 26

Download 26 pages 9.26 Kb

Page 2

INTRODUCTION

INTRODUCTION

This Job Aid, KUD01 STAINLESS STEEL DISHWASHERS, Part No. 4317288 provides specific infor- mation on the operation, diagnosis and repair of the KitchenAid KUD01 series Stainless Steel Dish- washer.

KUD01 STAINLESS STEEL DISHWASHERS has been compiled to provide the most recent informa- tion on design, features, operation, troubleshooting, and repair procedures.

GOALS AND OBJECTIVES

The goal of this Job Aid is to provide detailed information that will enable the service technician to properly diagnose malfunctions and repair the KUD01 Stainless Steel Dishwasher.

The objectives of the Job Aid are:

The service technician will -

•Understand proper safety precautions.

•Successfully troubleshoot and diagnose malfunctions.

•Successfully perform necessary repairs.

•Successfully return the dishwasher to proper operational status.

TO THE INSTRUCTOR/INDEPENDENT STUDENT

This Job Aid is designed to be used with the video tape, KUD01 STAINLESS STEEL DISHWASH- ERS, Part No. 4317287V.

KITCHENAID CORPORATION ASSUMES NO RESPONSIBILITY

FOR ANY REPAIRS MADE ON OUR PRODUCTS BY ANYONE

OTHER THAN AUTHORIZED SERVICE TECHNICIANS.

© 2000 KitchenAid, Inc., St. Joseph, MI 49013

II

Image 2

KitchenAid KUD01, KAD-7 manual Introduction, Goals And Objectives, To The Instructor/Independent Student

Contents

JOB AID KUD01 STAINLESS STEEL DISHWASHERKAD-7 TECHNICAL EDUCATIONGOALS AND OBJECTIVES OTHER THAN AUTHORIZED SERVICE TECHNICIANSINTRODUCTION TO THE INSTRUCTOR/INDEPENDENT STUDENTCOMPONENT ACCESS TABLE OF CONTENTSINSTALLATION CONSIDERATIONS TROUBLESHOOTING AND DIAGNOSISSAFETY WHAT TO DO IF THE DISHWASHER DOOR DOES NOT OPENAdditional Considerations INSTALLATION CONSIDERATIONSAPF Pressure Switch Trip Point 10 In. Water Column LOWER SPRAY ARM ROTATION 25 TO 40 RPMKEYPAD MATRIX SWITCHMODEL SPECIFIC TABLES INTERFACEMODEL KUDR01TJ - 4” Console MODEL KUDS01IJ - 4” Console THEORY OF OPERATIONMODEL KUDI01TJ - 6” Console MODEL KUDM01TJ - 6” Console MODEL KUDS01DJ - 4” Split ConsoleSOIL SENSING First Fill Water TemperatureWATER HEATING RINSE AID SENSINGFILL WASH/RINSE DRAIN DISPENSER VENT HEAT DRY STRIP CIRCUITSAUTOMATIC PURGE FILTRATION APF WIRING DIAGRAM TECH TIPSCANCELING A CYCLE CHANGING A CYCLESani Rinse OPTION SELECTIONSHi Temp Scrub Energy Saver DryDiagnostic Cycle Time Chart To Delay the StartDIAGNOSTICS CYCLE NOTE 1 - R/A SENSOR ASSEMBLY CHECK DIAGNOSTICS CYCLE TIME CHART NOTESNote HIGH TEMP SCRUB = POWER SCOUR = HIGH TEMP SCOUR DIAGNOSTICS CYCLE NOTE 2 - THERMISTOR OPEN/SHORT DETECTIONWash/Rinse Function NOTE 11 - HEATER ON - QUICK CLEANUP/TIME SAVER CYCLE ONLYNOTE 14 - POWER SCOUR/HIGH TEMP SCRUB OPTION NOTE 9 - SOAKING PAUSE INTERVAL - ENERGY STAR NORMAL CYCLE ONLYNOTE 8 - ‘END-OF-CYCLE’ STATUS INDICATORS - CLEAN and SANITIZED NOTE 6 - WATER HEATING THERMAL HOLD STATUS INDICATORNOTE 7 - SOAKING/SENSING & SOAKING STATUS INDICATORS a CleanAPF Function First Five Seconds NOTE 2 - APF ENABLED INTERVALSAutomatic Purge Filtration APF Function Last Five SecondsNOTE 1 - CYCLE MODIFICATIONS BASED ON SENSOR INPUTS COMPONENT ACCESSb Time Saver/Quick CleanUp Cycles a Anti-Bacteria/Cookware, Pots & Pans/Heavy, Normal, and China CyclesElectrostatic Discharge ESD Sensitive Electronics Using the Common Cycle Time ChartDisconnect power before servicing the dishwasher Removing the Console PanelALL MODELS Removing the Door Latch AssemblyRemoving the Electronic Control Board SPLIT CONTROL MODELSCommon Cycle Time Chart Layout HOW TO USE THE COMMON CYCLE TIME CHARTRemoving the Door Latch Microswitch Removing the Active Vent AssemblyRemoving the Inner Feed Tube and Lower Spray Arm Removing the Dispenser AssemblySERVICING COMPONENTS INSIDE THE TUB Removing the Water Inlet COMMON CYCLE TIME CHART 11 XTHIS IS THE FOLDOUT PAGE FOR THE Servicing the Heating ElementRemoving the Overfill Assembly Servicing the Overfill AssemblyRemoving the Overfill Control Switch or stops during a cycle TROUBLESHOOTING AND DIAGNOSISDishwasher does not run Dishwasher will not fillDrip Shield Removing the Wash MotorSeparation Screen Chopper Screen Bolt Holds DripTo Remove the Volute Accessing Components in the Sump AssemblyRemoving the Impeller from the Wash Motor