ElectricalRequirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

If the house has aluminum wiring, follow the procedure below:

1.Connect a section of solid copper wire to the pigtail leads.

2.Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

INSTALLATION INSTRUCTIONS

PrepareLocation

It is recommended that the vent system be installed before the range hood is installed.

Before making cutouts, make sure there is proper clearance within the ceiling or wall for vent fittings.

1.Disconnect power.

2.Determine which venting method to use: roof, wall, or non- vented.

3.Select a flat surface for assembling the range hood. Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift range hood onto covered surface.

2.Measure and mark center lines for the ³⁄₄" (1.9 cm) holes as shown. Use a ³⁄₄" drill bit and drill the 2 holes at the marked locations.

10⁷⁄₈" (27.6 cm) 10⁷⁄₈" (27.6 cm)

3"

3"

(7.6 cm)

(7.6 cm)

³⁄₄" (19 mm) diameter hole

3.Measure and mark lines as shown. Use a saber saw or keyhole saw to cut an opening through the underside of the cabinet.

Range Hood Cabinet Cutout

2" (5.1 cm)

10⁵⁄₈" (27 cm)

1.Determine and clearly mark a centerline on the underside of the cabinet.

⁄₄"

(23.5 cm)

A

A. Centerline

1" (2.5 cm)

11⁵⁄₈" (29.5 cm)

7

Page 7
Image 7
KitchenAid W10342488A Installation Instructions, ElectricalRequirements, PrepareLocation, Range Hood Cabinet Cutout

W10342488A specifications

The KitchenAid W10342488A is a versatile and efficient appliance accessory designed to elevate your cooking experience in the kitchen. Compatible with various KitchenAid stand mixers, this attachment serves as a powerful helper for both novice cooks and seasoned chefs.

One of the standout features of the W10342488A is its robust construction. Made from high-quality materials, it ensures durability and longevity, allowing users to perform a wide range of culinary tasks without worrying about wear and tear. The attachment boasts a sleek and modern design that seamlessly integrates with the aesthetic of KitchenAid stand mixers, enhancing their overall appeal.

Equipped with a powerful motor, this attachment delivers consistent performance whether you’re mixing dough, whipping cream, or preparing batters. Its efficiency allows for faster meal preparation, making it a valuable addition to any kitchen. The bowl lift design ensures stability during operation, enabling users to mix even the heaviest ingredients with ease.

Another key aspect of the W10342488A is its user-friendly interface. Featuring intuitive controls, it simplifies the mixing process, allowing users to adjust speeds according to their needs. The attachment also includes various speed settings, providing flexibility for different recipes and textures. Whether you want to create a fluffy meringue or a dense bread dough, the W10342488A has you covered.

Moreover, the attachment incorporates advanced mixing technology that allows for the even distribution of ingredients. This ensures that your recipes turn out perfectly every time, enhancing the quality of your culinary creations. The design also promotes easy cleaning, with some components being dishwasher safe, contributing to a hassle-free cooking experience.

In addition to its practical features, the KitchenAid W10342488A is backed by the brand's reputation for innovation and quality. KitchenAid is known for producing reliable kitchen appliances that inspire creativity and efficiency in cooking. With the W10342488A, users are equipped to explore new recipes and culinary techniques, making it an essential tool for enhancing the home cooking experience.

In conclusion, the KitchenAid W10342488A attachment stands out for its durability, efficiency, and user-friendly design. Featuring advanced technology and versatile capabilities, this appliance is perfect for anyone looking to elevate their culinary skills while enjoying the time-saving benefits of a KitchenAid mixer.