KitchenAid W10379132A Parts Supplied, Style 2 Copper Line Connection, Connect to Refrigerator

3.	Place the end of the tubing into a bucket, and turn shutoff	Connect to Refrigerator
	valve ON.
4.	Check for leaks. Tighten any nuts or connections (including	Parts Supplied:
	connections at the valve) that leak.
Style 2 - Copper Line Connection		■ ¹⁄₄" to ¹⁄₄" (6.35 mm to 6.35 mm) male-to-male coupling
NOTE: If there is a water supply line that meets the specifications
in “Water Supply Requirements,” proceed to “Connecting to
Refrigerator.” If not, use the following instructions to connect to
the household cold water supply.
1.	Unplug refrigerator or disconnect power.
2.	Turn OFF main water supply. Turn ON nearest faucet long
	enough to clear line of water.
3.	Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water
	pipe near the refrigerator.
	IMPORTANT:
	■ Make sure it is a cold water pipe.
	■ Horizontal pipe will work, but drill on the top side of the		1"
			(2.54 cm)
	pipe, not the bottom. This will help keep water away from	7"
	the drill and keep normal sediment from collecting in the	(17.78 cm)
	valve.

4.Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a cordless drill, drill a ¹⁄₄" (6.35 mm) hole in the cold water pipe you have selected.

	A
G	B
	C
F E	D
A. Cold water pipe	E. Compression sleeve
B. Pipe clamp	F. Shutoff valve
C. Copper tubing	G. Packing nut

NOTE: The flexible, codes approved water supply line can connect to the supply valve through the floor or through the side cabinets, as indicated by the gray boxes above.

1.Unplug the refrigerator or disconnect power.

2.Connect the 7 ft (2.13 m) flexible codes approved water tube to the water supply valve.

3.Flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear.

4.Tape the 7 ft (2.13 m) flexible codes approved water supply line to the floor, 7" (17.78 cm) from the left side of the refrigerator. Tape along the length of the tubing, which will allow it to pass beneath the refrigerator without interference.

D. Compression nut

6.Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

NOTE: Allow a minimum of 26" (66.04 cm) of flexible codes approved water supply line to be loose at the front of the refrigerator for connecting to the refrigerator.

5.Connect the 7 ft (2.13 m) flexible codes approved water supply line to the refrigerator.

NOTE: If the main water shutoff valve is behind the refrigerator, a secondary water shutoff valve may be installed in line with the water supply line at the front of the product.

7.	Slip the compression sleeve and compression nut on the
	copper tubing as shown. Insert the end of the tubing into the
	outlet end squarely as far as it will go. Screw compression nut
	onto outlet end with adjustable wrench. Do not overtighten the
	clamp or the sleeve. This will crush the copper tubing.
8.	Turn off the shutoff valve on the water pipe. Coil the copper
	tubing.
9.	Connect the flexible, codes approved water supply line to the
	water shutoff valve by threading the provided nut onto the
	shutoff valve.
10.	Place the end of the tubing into a bucket, and turn shutoff
	valve ON.

C

B

A

D

E

F G

11. Check for leaks around the saddle valve. Tighten any nuts or

connections (including connections at the valve) that leak.

A. Household water line	E. Bulb
B. Nut (purchased)	F. Nut
C. Ferrule (purchased)	G. Refrigerator water tubing
D. Coupling

6.Turn on the water supply valve and check all connections for leaks.

22