Manuals / Kodak / Computer Equipment / Printer

Kodak SRP 30 manual Inserting the Chemical Filters, Stabilizer, Bleach-Fix, Developer

Models: SRP 30

1 310

Download 310 pages 9.58 Kb

Page 73

Operator’s Guide

Stabilizer

1.Add 10.3 L of water to the first tank.

2.Add one-half the contents (approximately 72 mL) of one bottle of stabilizer concentrate (labeled SB).

3.Repeat Steps 1 and 2 for each of the three remaining stabilizer tanks. The total volume for each tank is 11 L.

Bleach-Fix

You can mix the working bleach-fix tank directly from the two-part concentrates. Use two EKTACOLOR Processing Cartridge 75 units to supply the two bottles of each of the two concentrate solutions.

CAUTION:

Avoid contamination of the developer with bleach-fix.

1.Add 12.7 L of water to the tank.

2.Add the entire contents of two bottles of bleach-fix concentrate, Part A (labeled BX-A).

3.Add the entire contents of two bottles of bleach-fix concentrate, Part B (labeled BX-B).

The total volume in the tank is 18.0 L.

Developer

IMPORTANT: To obtain good performance, take special care in mixing the developer tank.

1.Add 15.9 L of water to the tank.

2.Slowly add the entire contents of two bottles of developer concentrate (labeled CD).

3.Add 900 mL of EKTACOLOR RA Developer Starter, Catalog No. 102 6681. The total volume in the tank is 18.5 L.

Inserting the Chemical Filters

1.Take the chemical filters out of the accessory pack.

2.Rinse the filters in water to remove loose fibers and attach the filters to the holders.

3.Put them in the appropriate tanks corresponding to the colored stickers. You may need to turn the filter rods slightly so that the filters sit correctly.

3-6	KODAK PROFESSIONAL SRP 30 Laser Printer

Image 73

Kodak SRP 30 manual Inserting the Chemical Filters, Stabilizer, Bleach-Fix, Developer

Contents

SRP30 Laserprinter Operator’s Guide Kodak Professional SRP 30 Laser Printer Page Table of Contents Production MaintenanceContents Regulatory and Safety InformationRegulatory Compliance Mechanical Hazard Symbol Laser Compliance and SafetyOperator’s Guide Side Laser Source Label Locations of Laser Safety LabelsGeneral Precautions Safety PrecautionsWhen Operating the Equipment When Disposing of the EquipmentDisposal of Chemicals and Containers Handling of Processing ChemicalsGeneral Guidelines Safety Precautions for the Handling of ChemicalsSkin and Eye Protection Storage and DisposalWarranty Period Warranty InformationWarranty Repair Coverage How to Obtain ServiceLimitations Introduction Structure Using the DocumentationText Styles Urgent type of noticeConsumable Storage Requirements Storage of Chemicals and PaperOperator’s Guide Kodak Professional SRP 30 Laser Printer Overview Numeric Keypad Reorder Keyboard General Description Operator’s Guide Product Description Image Editing Film Advance and Paper Transport Functional ProcedureScanner Printer Main ComputerSorter Paper ProcessorDensitometer Automatic Startup Starting the EquipmentManual Startup System Startup Status User LoginReadiness for Operation Start Screen Changing Users End of WorkTouch Change user Operator’s Guide Automatic Shutdown Shutting DownManual Shutdown Touch ShutdownNext Login Change TimerTurning Off the Equipment Partially Sleep Mode Buttons and Lamp on the Main Computer Description of the Operating ControlsFilm stop button Touch-screen Monitor Screen Structure Information Area Overview Touch-sensitive Buttons Drop-down Menus Pop-up Windows Overview Input Screen Numeric Keypad Key Function Reorder KeyboardMenu Overview Print mode Settings Test Pricing + Statistics End of workMenu Bar Main MenusPrint Mode Menu Settings Menu without Equipment Settings Settings Menu with Equipment Settings Test Menu Pricing + Statistics Menu End of Work Menu Status Information and Help Menus Other Screens Info and Help Overview Film Drive Info Info Printer Info Paper Processor Info Order Version Info Error List Error Help Index Waiting CancelHelp Help IndexChemicals Operator’s Guide Kodak Professional SRP 30 Laser Printer Preparation of Chemicals Rinsing the Tanks After each preparation of a solution, thoroughly rinseFollowing order With hot waterRegion CAT No Mixing the Tank SolutionsStabilizer Inserting the Chemical FiltersBleach-Fix DeveloperPreparing Replenisher Tank Temperature COther Operations to Perform Prior to Production Settings Production Balance Digital Digital Order Settings From the Order Receipt to the Finished Print AdministratorOperator Load settings SettingsEntering Names Entering Numbers Settings Machine settings Machine SettingsConfiguration Surface and Paper settings Cut length MachineSettings Machine settings Surface Install SoftwareDefining Surfaces Network orders Digital ordersOperator’s Guide Settings Machine settings Paper settings Defining Paper SettingsOperator’s Guide Coding the Paper Magazine Width Indicators Surface Indicators Paper WidthDefining the Cut Lengths Settings Machine settings Cut lengthPaper width Minimum cut length Comments User Interface Settings Machine settings User manager User Administrator Defining Users and User RightsTouch Password Touch Old PasswordUser Profiles Settings Machine settings Startup Defining Times for Startup, Shutdown, and Sleep ModeUnder the No operator actions heading Calendar Defining Off Days Settings Machine settings Startup Edit calendarSettings Machine settings Install Software Installing the SoftwareVersion Info Enabling the SoftwareImporting a Combiprint Layout Settings Machine settings Combiprint LayoutImporting an Index Print Layout Settings Machine settings Index print layoutPrinter Settings Settings Machine settings Scanner Scanner SettingsScratch correction Scanning crop and Slide cropSetting the Replenishment Rates Paper Processor SettingsSettings Machine settings PP Replenishment Calibrating the Temperature Sensors and Water Pumps Production Balance TFS Logic Settings Machine settings Production BalanceImpact Sharpen Edges, Saturation, and Sharpen Grain Panorama Identification Contrast Management Area Contrast, Detail ContrastLearning TFS Learns and Learning TFS Used Learning TFS ResetTFS Color Color/Density LogicIncreasing the standard values Advantages Disadvantages Reducing the standard valuesAdvantages Disadvantages Reducing Parameter Function Setting rangeStandard ValuesParameter for Cross Curve Compensation Cross curve compensation Cross curve behaviorTFS Density Parameter Function Setting RangeSelector Logic and TFS Selector Parameter Selected Setting Description RangeTouch Color correction Color CorrectionTouch DX correction DX CorrectionOperator’s Guide Production Balance Digital Settings Machine settings Production BalanceOperator’s Guide Settings Machine settings Network orders Digital Order SettingsNetwork orders Set Autom. printing to Off Operator’s Guide Settings Machine settings Other Other SettingsLab ID and Lab name Automatic end of order and Film lengthTouch Save or Cancel Print ConfigurationsSettings Print configurations DTFS PreselectionSettings Creating a New Configuration Creating, Editing, and Deleting ConfigurationsCreating a New Configuration Based on an Existing One Modifying a Configuration Paper ConfigurationsDeleting a Configuration Settings Print configurations PaperAPS Sizes Print SizesSettings Print configurations Back print Back Print ConfigurationsClassic High Vision Panorama Paper Width Inches Paper Width InchesAdditional Information Regarding Certain Parameters Settings Settings Print configurations Index print Index Print ConfigurationsAPS Back Print APS Film dataLayout Paper ConfigPrint Length Index PrintsSettings Print configurations Corrections Correction ConfigurationsSettings Settings Print configurations Autosave Autosave ConfigurationsAutosave fixed PDM Autosave qualitySettings Print configurations Front print Front Print ConfigurationsOperator’s Guide Settings Print configurations Combiprint Combiprint ConfigurationsLayout Settings Print configurations Order Order ConfigurationsPackage SingleReproduction Single Configurations Film Mask File Print Example Adjust Longer sideFilm Mask APS IX APS Film Sizes Aspect ratio Film Mask Slide Package Configurations Combiprint Configurations Reproduction Configurations When Scanning Color Negative Film Configuration Types in the Order Configuration ListWhen Scanning Black-and-White Film Black-and-White PrintsDefining a Standard Configuration Pricing Configurations Settings Save settings Save / Load Settings and ConfigurationsTo save To load Settings Load settingsTests Operator’s Guide Kodak Professional SRP 30 Laser Printer Printer Tests IntroductionOverview Printing a PBL Test Prerequisites for MBL and PBL CalibrationTest Start PBL PBL Test with Laser Point Test Start MBL Printing an MBL TestEnable with Laser point Daily Calibration without the MBL Daily Calibration with the MBLCompletion of the New Calibration Calibration of New Paper, Emulsion Changes Master PaperScanner Calibration Piko Test Start Piko To start Piko manuallyTesting the Paper Processor Test Control strip Chemical control strip Operator’s Guide Kodak Professional SRP 30 Laser Printer Production Autoprint Print Mode Reorder Mode Manual Positioning Mode Preparing the Equipment for Different Orders Adjusting the Paper WidthPreparing the Paper Magazine Operator’s Guide Installing Paper Coding the Paper Magazine Width Indicators Surface Indicators Paper WidthExcessive insertion force on the paper magazine can cause Changing the Paper MagazineDamage to the drive gear Changing the Film Mask Changing the Mirror Box for 120 FilmsAPS Film Handling APS FilmAPS Film Cartridge Typical Order Tracking Order HandlingPrerequisites Starting the Order Inserting Film into the Film FeederThese print modes Print order starts Manual Order Numbering Order Number Automatic or ManualTouch the Change Order no.? button Automatic Order Numbering End of Order Automatic or ManualNormal Print Modes Print Modes OverviewDigital Print Modes Current Configuration Screen Using Print ConfigurationsEditing the Current Configuration Changing the Order ConfigurationSelecting a New Order Configuration Printing Changing the Order NumberPrint mode Autoprint Autoprint Print ModeOperator’s Guide For short film strips 400 mm Print mode Reorder Reorder ModeTouch Edit order Production Operator’s Guide Production Operator’s Guide Print mode Manual positioning Manual Positioning ModeOperator’s Guide Inserted in the film mask, the film piece might not be in a If the printer is reset with a film piece one or two framesRemove the film mask, you risk damaging the film DTFS Only for File Print File Print ModePrinting from Digital Media Print mode File printPictures Touch Start printing or Save order Saving Digital Orders File Prints Production Touch Start printing Touch Prepare Order Printing Digital Images without PreviewPrinting Digital Images with Preview Screen that is used for resetting the printerProduction Print mode Slide print Slide Print ModeTouch Order end Finishing the OrderUsing Preview Production Touch Colour/dens. corrections Image EditingTouch Improve Image Area contrast Detail contrast Sharpness Saturation Production Scan Troubleshooting Image Quality Problems Symptom SolutionTouch Format text SpecialOperator’s Guide Production Operator’s Guide Touch Save on the Image editing and Special screens Saving Image Data in a FileImages in the Network Starting Network Orders Printing Network OrdersOperator’s Guide Index Prints Configuring Index Print LayoutFilm Strips Index Prints in the Different Print Modes Number / Aspect Ratio of the Single Images per Index PrintFor Reorders Print Only Index PrintFor Packages For File PrintsPrinting Price Labels Option Saving Statistics StatisticsPricing + Statistics Save Statistics Pricing + Statistics Show Statistics Viewing StatisticsCorrecting System Conditions Avoiding Handling Errors System ErrorsError Messages Correcting System Conditions Reset Using the Film Stop Key On key Resetting the EquipmentFilm stop key Reset Using the Stop Button on the Screen Important Do not pull out the film mask during a reset Reset Using the on KeyUnresolved Errors Error HandlingGeneral Image Processing Errors Gray Screen After ResetPaper Processor Errors Fill PrintOther Error Situations Printer ErrorsHelp in Case of Error Messages Shutter not reached MR, ML SGLS01 not reachedRemoving Paper Jams Paper Jams in the Transport Unit Paper Jams in the Printer SectionBefore pulling out the transport unit Close the lever Transport Unit at the BottomSheet Bridge to Transport Unit Transport at the TopOperator’s Guide Correcting System Conditions Paper Jams in the Print Engine Correcting System Conditions Paper Jams in the Lane Distributor Mechanical damage cannot be ruled out Paper Jams between the Lane Distributor and Sheet TransferPaper Jams in the Paper Processor Maintenance Other Consumables Kodak Professional Digital III Color Paper Maintenance Schedule and Maintenance Intervals Clean air filters Cleaning the APS Film Mask Daily MaintenancePrimary Procedure Cleaning the Drive Rollers in the Film MaskTouch Eject on the Manual positioning screen End of work Shutdown Alternate ProcedureTest Control strip Chemical control strip Performing a Process Control for the Paper ProcessorMaintenance Cleaning the Film Take-Up Weekly MaintenanceRemoving Dust from the Film Mask Cleaning the Film Chute Transport Unit Removing Paper Dust from the Printer SectionsSingle Sheet Buffer and Sheet Bridge Print Engine Maintenance Operator’s Guide Lane Distributor Sheet Transfer Maintenance Removing the CD Color Developer Feed Unit Opening and Closing the Wet Section CoverStack the crossovers Removing the Tank CrossoversRemoving the Squeegee Unit and V Wiper Damage Cleaning ProcedureChecking the Solution Levels Cleaning the Chemical Filters Cleaning the Filters in the Astor and Water Supplies Plates Cleaning the Densitometer Calibration PlateCleaning the Transport Belt of the Print Chute Cleaning the Exposure Filters Monthly MaintenanceOperator’s Guide They do not break When cleaning the very thin and highly fragile glassesBare hands Reinstalling them Cleaning / Replacing the Air FiltersLet washed filters and filter mats dry thoroughly before Do not wring, bend, or press the filters and filter matsLamp House Under the Cutter Unit CCD FanInto the print engine Door to the Print EngineOperator’s Guide Changing the Scan Lamp Do not bypass the lamp switch when the lamp mount is foldedFree cloth To avoid fingerprints, do not touch the lamp with your bareChanging the Chemical Filters Chemical splashes may stain the covers. Remove any splashes Cleaning the Processing RacksImmediately with water Maintenance Operator’s Guide Startup, be sure to disable the automatic MBL in order to Cleaning the Dryer RackPrevent a paper jam Operator’s Guide Cleaning / Replacing the Air Filter Cleaning the Paper OutletCleaning the Slide Plate with the Feed Chute Maintenance Operator’s Guide Removing the Dust from the Lens Maintenance When RequiredChanging the Ink Ribbon on the Back Printer Tanks is 20 L Emptying the Effluent TanksChemicals ConsumablesAir Filters Other ConsumablesRolls Surface Catalog No In. x ft Kodak Professional Digital III Color PaperOperator’s Guide Kodak Professional SRP 30 Laser Printer Page Eastman Kodak Company Eastman Kodak Company