RC-5 Commands for the Home Theater
Standard 7.1, continued
SYSTEM | COMMAND | SYSTEM | COMMAND | RC5 WORD | HOME THEATER |
(HEX) | (HEX) | (DEC) | (DEC) | (HEX) | STANDARD 7.1 |
|
|
|
|
|
|
19 | 5 | 25 | 5 | 3645 | TV |
19 | 6 | 25 | 6 | 3646 | CD |
19 | 7 | 25 | 7 | 3647 | TUNER |
19 | 8 | 25 | 8 | 3648 | AUX1 |
19 | 9 | 25 | 9 | 3649 | AUX2 |
19 | A | 25 | 10 | 364A | MAIN ZONE |
19 | B | 25 | 11 | 364B | ZONE 2 |
19 | C | 25 | 12 | 364C | USER |
19 | D | 25 | 13 | 364D | VCR INPUT |
19 | E | 25 | 14 | 364E | TAPE INPUT |
19 | 10 | 25 | 16 | 3650 | COMPONENT1 |
19 | 11 | 25 | 17 | 3651 | COMPONENT2 |
19 | 12 | 25 | 18 | 3652 | COAX3 |
19 | 13 | 25 | 19 | 3653 | COAX4 |
19 | 13 | 25 | 19 | 3654 | COAX5 |
19 | 15 | 25 | 21 | 3655 | COAX6 |
19 | 16 | 25 | 22 | 3656 | TRIGGER1 ON |
19 | 17 | 25 | 23 | 3657 | TRIGGER1 OFF |
19 | 18 | 25 | 24 | 3658 | TRIGGER2 ON |
19 | 19 | 25 | 25 | 3659 | TRIGGER2 OFF |
19 | 1A | 25 | 26 | 365A | TRIGGER3 ON |
19 | 1B | 25 | 27 | 365B | TRIGGER3 OFF |
19 | 1C | 25 | 28 | 365C | TRIGGER4 ON |
19 | 1D | 25 | 29 | 365D | TRIGGER4 OFF |
19 | 1E | 25 | 30 | 365E | Z2 PWR ON |
19 | 1F | 25 | 31 | 365F | Z2 PWR OFF |
19 | 20 | 25 | 32 | 3668 | MAX DYNR |
19 | 21 | 25 | 33 | 3669 | NIGHT DYNR |
19 | 22 | 25 | 34 | 366A | NORM DYNR |
1C | 14 | 28 | 20 | 3714 | EQ OFF |
1C | 15 | 28 | 21 | 3715 | EQ MEM1 |
1C | 16 | 28 | 22 | 3716 | EQ MEM2 |
1C | 17 | 28 | 23 | 3717 | EQ MEM3 |
1C | 18 | 28 | 24 | 3718 | EQ MEM4 |
19 | 30 | 25 | 48 | 3670 | DIGIT 0 |
19 | 31 | 25 | 49 | 3671 | DIGIT 1 |
19 | 32 | 25 | 50 | 3672 | DIGIT 2 |
19 | 33 | 25 | 51 | 3673 | DIGIT 3 |
19 | 34 | 25 | 52 | 3674 | DIGIT 4 |
19 | 35 | 25 | 53 | 3675 | DIGIT 5 |
19 | 36 | 25 | 54 | 3676 | DIGIT 6 |
19 | 37 | 25 | 55 | 3677 | DIGIT 7 |
19 | 38 | 25 | 56 | 3678 | DIGIT 8 |
19 | 39 | 25 | 57 | 3679 | DIGIT 9 |
19 | 3A | 25 | 58 | 367A | SET MODE** |
**The SET MODE command allows the user to set a specific audio decode mode using RC 5 commands. The code is set by sending the unit the SET MODE command, then the two DIGIT commands which define the mode. These three commands must occur in sequence; any command sent after the SET MODE command, other than the DIGIT commands, causes the SET MODE sequence to be reset. Refer to the list of audio decode modes on page 20. Modes that do not apply to the current input stream are ignored.
Krell Home Theater Standard 7.1 Developer’s Reference | 19 |