Installation | ¡ |
¿ |
3
(if applicable) |
|
|
|
|
|
|
|
|
| ||
¬ |
|
|
|
|
|
|
| stop ring (3) | stop ring (3) |
| |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| screw (1) |
|
| ||
|
|
|
| valve steam | stop post | ||||||
|
|
|
|
| driver (2) |
| (downward) | ||||
¿ |
|
|
|
|
|
|
| cartridge stem | stop ring |
| |
|
|
|
|
|
|
|
| close |
|
| |
|
|
|
| H |
|
|
|
|
|
| |
|
|
|
| (4) |
|
|
|
|
|
| |
|
|
| C |
|
|
|
|
|
|
| |
|
|
|
| (6) |
|
| stop post |
|
| ||
|
|
|
| (5) |
|
| (downward) |
|
| ||
|
|
|
|
|
|
|
|
|
| ||
Close |
|
|
|
| - Put the | ||||||
- | Once shower enclosure is completed, remove the finished wall template. |
|
| cover, on which the | |||||||
¡ | - | If the valve body is equipped with service stop valves close the hot and | - | Position the valve cover with stop post facing | down. Seat the cover to the | ||||||
| cold water supplies. Otherwise, shut the supply at the nearest source. |
| body. Do not pinch the | ||||||||
|
|
|
|
|
| minimum | of pressing force. |
|
| ||
Remove valve stem driver and stop ring: | - Tighten up the cover screws diagonally, first lightly and then more | ||||||||||
- | Remove the screw (1) to remove the plastic valve stem driver (2). |
| firmly. |
|
|
| |||||
¬ | - | Remove stop ring (3) note position. |
|
|
|
|
| ||||
|
|
|
|
| Fix stop ring on closed position: |
|
| ||||
Turn cartridge for | - | Close the | valve by turning the | cartridge stem | clockwise. | ||||||
- | Remove the four cover screws (4) and the valve cover (5) with |
| - Position the stop ring on the stem as shown in figure 4. | ||||||||
| - Pull the cartridge out. Do not damage the |
| - Install plastic stem driver (2) with screw (1). |
| |||||||
| - | Rotate the cartridge 180° | turning | it upside down. Place it into the valve |
|
| ¡ |
|
|
| |
|
| body. Note position of hot ("H") and cold ("C") markings on the cartridge: |
|
|
|
|
| ||||
|
| "H" hot will now be on the right and "C" cold on the left. Two alignment pins |
|
|
|
|
| ||||
|
| located on the rear of the cartridge must sit in the locating holes within the |
|
|
|
|
| ||||
|
| valve body. Cartridge is correctly | engaged when pushing the cartridge, it |
|
|
|
|
| |||
|
| will not rotate. |
|
|
|
|
|
|
|
| |
Installation of the trim set and setting the hot limit stop |
|
|
|
| 4 | ||||||
|
|
|
|
|
|
|
|
|
| ||
|
| (7)¿ | Do not overtighten ! |
|
| A) |
| B) | |||
|
|
|
|
| close | hot limit ring (10) | |||||
|
|
|
|
|
|
|
| ||||
|
|
|
| valve stem |
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||
|
|
|
| driver (2) |
|
|
|
|
|
| |
|
|
| (1) | (7) | rotating of the stem |
|
| ||||
|
|
| (9) to the desired |
|
| ||||||
|
|
|
|
|
|
| |||||
|
|
|
|
| max. temperature |
|
| ||||
¿ | ! |
|
|
| ¡ |
| max. hot temperatur | (9) | stop post | ||
|
|
| (8) |
|
|
| Torx 20 |
| |||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| |||
Installation of the escutcheon (8): |
| Setting hot limit stop: |
|
| |||||||
|
|
|
|
|
|
|
|
|
| ||
| Install escutcheon screws (7) into valve cover posts. |
| A) Rotate escutcheon driver stem (9) counterclockwise until a desired and safe | ||||||||
| Slide the escutcheon (8) over the screw heads and rotate escutcheon |
|
| hot water temperature is reached (recommened maximum is 110°F / 43°C) | |||||||
| counterclockwise. |
|
|
|
| B) Place the hot limit ring (10) over the splines on the stem (9) with the hot limit | |||||
| Tighten the screws (7) so the escutcheon is firmly pressed against the wall and |
|
| ring resting against the stop post on the escutcheon. | |||||||
| does not rotate. Do not overtighten! |
|
| Closing the valve while rotating the stem (9) clockwise until it stops, | |||||||
|
|
|
|
|
| ¬Install the handle. |
|
| |||
