Lancom Systems 3550 - page 34

LANCOM 3550 Wireless

 Chapter 3: Basic configuration

34

EN

then the device can be accessed by the name “LANCOM <MAC address>”

(e.g. “LANCOM-00a057xxxxxx”).

The MAC address can be found on a label at the bottom of the device.

If there is no DNS se rver in the LAN, or it is not link ed to the DHCP se rver,

then the device can not be reached by the name. The following options

remain in this case:

Figure out the DHCP-assigned IP address of the LANCOM by suitable

tools and contact the device directly with this IP address.

Use LANconfig.

Connect a PC with a terminal program via the serial configuration

interface to the device.

Starting the wizards in WEBconfig

햲Start your web browser (e.g. Internet Explorer, Netscape Navigator,

Opera) and call the LANCOM Router there:

http://<IP address of the LANCOM>

(or with a name as discribed above)

If you cannot access an unconfigured LANCOM Router, the problem

may be due to the netmask of the LAN: with less than 254 possible

hosts (netmask > '255.255.255.0'), please ensure that the IP address

'x.x.x.254' is located in your own subnet.

The WEBconfig main menu will be displayed:

Contents

Main Page Preface Page Page Contents Page Page 1Introduction 1.1 What is a Wireless LAN? 1.1.1 Which hardware to use? 1.1.2 Operation modes of Wireless LANs and base stations 1.2 The advantages of the UMTS/HSPDA solution 1.2.1 Last mile via UMTS/HSPDA 1.2.2 Mobile conference room 1.2.3 UMTS/HSPDA Backup Page 1.3 What can your LANCOM Router do? Page Page 2 Installation 2.1 Package contents 2.2 System preconditions 2.3 Status displays, interfaces an hardware installation 2.3.1 Status display Page Page 2.4 The back of the unit 2.5 Hardware installation 2.6 Software installation Page 2.6.1 Starting LANCOM setup 2.6.2 Which software should you install? Page 3 Basic configuration 3.1 Which information is necessary? 3.1.1 TCP/IP settings Page 3.1.2 Configuration protection 3.1.3 Settings for the Wireless LAN 3.1.4 Settings for the DSL connection 3.1.5 Connect charge protection Page Page Page 3.5 TCP/IP settings to workstation PCs Page 4 Setting up Internet access 4.1 Instructions for LANconfig 4.2 Instructions for WEBconfig Page 5 Setting up the UMTS profile 5.1 Internet access Page Page 5.2 VPN site coupling Page 5.3 Other settings 5.3.1 Choosing the mobile telephone network 5.3.2 Activate UMTS/GPRS profile 5.3.3 UMTS/HSPDA only or automatic UMTS/HSPDA/GPRS selection Page 6 Point-to- point connections 6.1 Antenna alignment for P2P operations 6.2 Configuration Page 6.3 Access points in relay mode 6.4 Security for point-to- point connections 6.4.1 Encryption with 802.11i/WPA Page 6.4.2 LEPS for P2P connections 7 Security settings 7.1 Security for the Wireless LAN 7.1.1 Closed network 7.1.2 Access control via MAC address 7.1.3 LANCOM Enhanced Passphrase Security 7.2 Tips for handling keys 7.3 The security settings wizard 7.3.1 Wizard for LANconfig 7.3.2 Wizard for WEBconfig 7.4 The firewall wizard 7.4.1 Wizard for LANconfig 7.4.2 Configuration under WEBconfig 7.5 The security checklist Page Page Page Page 8 Options and accessories 8.1 Optional LANCOM Wireless Router antennas 8.1.1 Antenna Diversity 8.1.2 Installation of AirLancer Extender antennas 8.2 LANCOM Public Spot Option Page 9Troubleshooting 9.1 PIN Handling Page 9.2 No DSL connection is established 9.3 DSL data transfer is slow 9.4 Unwanted connections under Windows XP 75 EN 10 Appendix 10.1 Performance data and specifications LANCOM 3550 Wireless 76 EN 10.2 Contact assignment 10.2.1 LAN interface, 10/100base-TX 10.2.2 WAN interface, 10/100base-TX 10.3 Declaration of conformity Page Index