Lancom Systems 3550 10 Appendix

LANCOM 3550 Wireless

 Chapter 10: Appendix

75

EN

10 Appendix

10.1 Performance data and specifications

LANCOM 3550 Wireless

Frequency band 2400 - 2483,5 MHz (ISM) or 5150 - 5750 MHz

Connections LAN 10/100base-TX, autosensing, node/hub switch

WAN 10/100base-TX, autosensing

WLAN1 Two reverse SMA connections with antenna diversity

WLAN2 32 bit cardbus interface for optional second radio card

Power supply 12V AC via external power supply adapter, or Power over Ethernet by IEEE 802.3 draft stan-

dard

Antenna connection Two reverse SMA connections for external LANCOM AirLancer-Extender antennas and 3-dBi-

dipol dualband antennas (in package contents)

Please respect the restrictions given in your country when setting up an antenna system. For

information about calculating the correct antenna setup, please refer to

www.lancom-systems.com.

Housing 210mm x 143mm x 45mm (B xHx T), rugged plastic case, stackable, provision for wall moun-

ting

Norms CE compliant according to ETSI EN 300 328, ETSI EN 301 893, ETSI EN 301 489-1, ETSI EN

301 489-17, EN 60950

Radio licenses for all EU countries and Switzerland

Regulations Notified in Germany, Belgium, Netherlands, Luxemburg, Austria, Switze rland, United King-

dom, Italy, France

Environment Temperature range 0°C to +50 °C at 95% max. humidity (non condensing)

Service Warranty: 3 years

Support Via hotline and Internet

Contents

Main Page Preface Page Page Contents Page Page 1Introduction 1.1 What is a Wireless LAN? 1.1.1 Which hardware to use? 1.1.2 Operation modes of Wireless LANs and base stations 1.2 The advantages of the UMTS/HSPDA solution 1.2.1 Last mile via UMTS/HSPDA 1.2.2 Mobile conference room 1.2.3 UMTS/HSPDA Backup Page 1.3 What can your LANCOM Router do? Page Page 2 Installation 2.1 Package contents 2.2 System preconditions 2.3 Status displays, interfaces an hardware installation 2.3.1 Status display Page Page 2.4 The back of the unit 2.5 Hardware installation 2.6 Software installation Page 2.6.1 Starting LANCOM setup 2.6.2 Which software should you install? Page 3 Basic configuration 3.1 Which information is necessary? 3.1.1 TCP/IP settings Page 3.1.2 Configuration protection 3.1.3 Settings for the Wireless LAN 3.1.4 Settings for the DSL connection 3.1.5 Connect charge protection Page Page Page 3.5 TCP/IP settings to workstation PCs Page 4 Setting up Internet access 4.1 Instructions for LANconfig 4.2 Instructions for WEBconfig Page 5 Setting up the UMTS profile 5.1 Internet access Page Page 5.2 VPN site coupling Page 5.3 Other settings 5.3.1 Choosing the mobile telephone network 5.3.2 Activate UMTS/GPRS profile 5.3.3 UMTS/HSPDA only or automatic UMTS/HSPDA/GPRS selection Page 6 Point-to- point connections 6.1 Antenna alignment for P2P operations 6.2 Configuration Page 6.3 Access points in relay mode 6.4 Security for point-to- point connections 6.4.1 Encryption with 802.11i/WPA Page 6.4.2 LEPS for P2P connections 7 Security settings 7.1 Security for the Wireless LAN 7.1.1 Closed network 7.1.2 Access control via MAC address 7.1.3 LANCOM Enhanced Passphrase Security 7.2 Tips for handling keys 7.3 The security settings wizard 7.3.1 Wizard for LANconfig 7.3.2 Wizard for WEBconfig 7.4 The firewall wizard 7.4.1 Wizard for LANconfig 7.4.2 Configuration under WEBconfig 7.5 The security checklist Page Page Page Page 8 Options and accessories 8.1 Optional LANCOM Wireless Router antennas 8.1.1 Antenna Diversity 8.1.2 Installation of AirLancer Extender antennas 8.2 LANCOM Public Spot Option Page 9Troubleshooting 9.1 PIN Handling Page 9.2 No DSL connection is established 9.3 DSL data transfer is slow 9.4 Unwanted connections under Windows XP 75 EN 10 Appendix 10.1 Performance data and specifications LANCOM 3550 Wireless 76 EN 10.2 Contact assignment 10.2.1 LAN interface, 10/100base-TX 10.2.2 WAN interface, 10/100base-TX 10.3 Declaration of conformity Page Index