Land Pride

Table of Contents

Section 1 Assembly and Set-Up

b.Pull driveline apart into two sections as shown in Figure 1-6. Attach the outer driveline universal joint to the tractor shaft and inner driveline universal joint to the tiller gearbox shaft. Pull on each driveline section to be sure the universal joints are secured to the shafts.

c.Hold driveline sections parallel to each other to determine if they are too long. The inner and outer shields on each section should end approximately 1" short of reaching the universal joint shield on the adjacent section (see “B” dimension). If they are too long, measure 1" (“B” dimension) back from the universal joint shield and make a mark at this location on the inner and outer driveline shields.

d.Cut off inner shield at the mark (“X” dimension). Cut the same amount off the inner shaft (“X1” dimension). Repeat cut off procedure (“Y” & “Y1” dimensions) to the outer driveline half.

e.Remove all burrs and cuttings.

13588

Shortening the driveline

Figure 1-6

Checking Driveline Maximum Length

Make sure you have gone through the steps in

"Checking Driveline Minimum Length" on page 10 before checking maximum length.

Refer to Figure 1-7

The driveline maximum length must, when fully extended, have a minimum overlap of the profile tubes by not less than 1/3 the free length with both inner and outer profile tubes being of equal length.

1.Apply multi-purpose grease to the inside of the outer shaft and reassemble the driveline.

2.Assemble the two driveline profiles together with just 1/3 overlapping of the profile tubes as shown in Figure 1-7. Measure and record this overall length for checking driveline length in step 9 below.

3.Attach inner driveline yoke end to the tiller gearbox input shaft.

4.Attach outer driveline yoke end to the tractor's PTO shaft.

5.The driveline should now be moved back and forth to insure that both ends are secured to the tractor and Rotary Tiller PTO shafts. Reattach any end that is loose.

24513

Outer Shielding has been removd for clarity.

Driveline Maximum Length

Figure 1-7

IMPORTANT: A small chain is supplied with the driveline. This chain must be attached to the inner driveline shield and to the tiller to restrict shield rotation.

6.Hook driveline safety chain in the hole in the inner driveline guard. Attach the other end to the tiller’s main frame.

7.Start tractor and raise tiller just enough to remove blocks used to support the tiller frame in step 3a on page 10.

8.Slowly engage tractor’s hydraulic 3-point to lower the Rotary Tiller. Check for sufficient drawbar clearance. Move drawbar ahead, aside or remove if required.

9.Raise and lower implement to find maximum extended driveline length. Check to make certain that the driveline overall length does not extend beyond the maximum recorded length in step 2.

5/05/06

RTA10 & RTA15 Series Rotary Tillers 311-252M

11

Page 12 Page 14
Page 13
Image 13
Land Pride RTA1542, RTA1550, RTA1050, RTA1058, RTA1558, RTA1042, RTA1034 manual Checking Driveline Maximum Length
Page 12 Page 14

RTA10, RTA1558, RTA15, RTA1550, RTA1034 specifications

Land Pride is a well-known manufacturer of high-quality agricultural and landscaping equipment, and their RTA series of tillers, including the RTA1042, RTA1050, and RTA1058, exemplify their commitment to performance and reliability. These rotary tillers are designed for use with a variety of tractors, making them an excellent choice for landscaping professionals, landscapers, and farmers looking to enhance soil aeration and prepare for planting.

The Land Pride RTA1042, RTA1050, and RTA1058 share several key features and technologies that set them apart in the market. All three models come with a heavy-duty, gear-driven design that provides maximum durability, allowing them to handle tough soil conditions with ease. This gear-driven system ensures a consistent power transmission from the tractor to the tiller, resulting in efficient soil tillage.

One of the standout characteristics of these tillers is their width options, catering to different operational requirements. The RTA1042 boasts a working width of 42 inches, making it perfect for smaller gardens and landscaping projects. The RTA1050 offers a 50-inch width, ideal for medium-sized fields and larger landscaping tasks. Lastly, the RTA1058 provides a wider 58-inch working width, suitable for larger agricultural applications and more extensive earth-moving tasks.

Additionally, these tillers feature adjustable tines that allow operators to tailor their tillage depth according to specific soil conditions and planting requirements. This feature not only enhances versatility but also promotes optimal soil health by allowing for different tillage practices.

The RTA series also includes a quick-attach system, ensuring easy installation and removal from the tractor. This design saves time and enhances productivity, allowing users to switch attachments swiftly as needed. Furthermore, the heavy-duty roller is equipped with adjustable height settings, enabling operators to control the tilling process effectively.

To summarize, the Land Pride RTA1042, RTA1050, and RTA1058 rotary tillers are engineered for durability, efficiency, and versatility. With their gear-driven design, adjustable tines, and varying widths, these tillers are suitable for a range of applications, from small garden beds to extensive agricultural fields. Whether for professional landscaping work or large-scale farming, these tillers stand out as robust implements that enhance soil preparation and promote successful planting outcomes.
Top Page Image Contents