Manuals / Land Pride / Lawn and Garden / Tiller

Land Pride RTR1050 manual Clutch Disassembly & Reassembly, Refer to -3 View - B, Table of Contents

Models: RTR1542 RTR1050 RTR1042 RTR1558 RTR1058 RTR1550

1 34

Download 34 pages 40 b

Page 22

Refer to Figure 4-3 (View - B):

Table of Contents

Section 4: Maintenance and Lubrication

Land Pride

4.Inspect the clutch and ensure that the scribed markings made on the clutch plates have changed position. Slippage has not occurred if any two marks on the friction disk and plate are still aligned. A clutch that has not slipped must be disassembled to separate the friction disk plates. See Clutch Disassembly & Reassembly on page 21.

Refer to Figure 4-3 (View - B):

5.Turn all 4 nuts fully back if no two marks on the friction disk and plate are still aligned. Clutch is ready for use.

6.The clutch should be checked during the ﬁrst hour of cutting and periodically each week. An additional set of scribe marks can be added to check for slippage.

Hex Head

Socket Bolts

21270

Clutch Run-In With 6- Hex Head Socket Bolts

Figure 4-2

22171

Clutch Run-In With 4 Tightening Nuts

Figure 4-3

Clutch Disassembly & Reassembly

Clutches With 8-Hex Head Socket Bolts

Refer to Figure 4-4

If the clutch run-in procedure, see Clutches With 8-Hex Head Socket Bolts, indicated that one or more of the friction disks did not slip, then the clutch must be disassembled to separate the friction disks.

1.Rotate 8 hex head socket bolts (#4) all the way out to free stop ﬂange (#5).

2.Rotate stop ﬂange (#5) and remove from housing (#1)

3.Remove the following inner components:

a.Spring kit (#6)

b.Pressure flange (#7)

c.1st Friction Disc (#8)

d.Hub with flange and pull collar (#2 & #3)

e.2nd Friction disc (#8)

f.Bearing (#9)

4.Inspect all components and replace to their original position. Make certain stop ﬂange (#5) is replaced with its ﬂanges down as shown.

5.Fully tighten all 8 hex head socket bolts (#4).

21302

Clutch Assembly

Figure 4-4

20 RTR10 & RTR15 Series Rotary Tillers 311-431M

5/05/06

Image 22

Land Pride RTR1050 Clutch Disassembly & Reassembly, Refer to -3 View - B, Table of Contents, Maintenance and Lubrication

Contents

RTR10 & RTR15 Series RTR1042, RTR1050 & RTR1058 Table of ContentsRotary Tillers RTR1542, RTR1550 & RTR1558Section 1 Assembly and Set-Up Table of ContentsImportant Safety Information Section 3 AdjustmentsImportant Safety Information Safety at All TimesLook For The Safety Alert Symbol Be Aware of Signal WordsTransport Machinery Safely Use Safety Lights and DevicesPractice Safe Maintenance Keep Riders Off MachineryAvoid High Pressure Fluids Hazard Prepare for EmergenciesWear Protective Equipment Table of Contentsa. Clean the area the label is to be placed Safety Labels2. Keep all safety labels clean and legible b. Spray soapy water on the surface where the label is to be placedTable of Contents 818-171C818-284C Important Safety InformationTable of Contents 818-552C818-858C Important Safety Information818-552C 818-543C818-540C Table of ContentsOwner Assistance Using This ManualApplication IntroductionTractor Requirements Section 1 Assembly and Set-UpTable of Contents Front Deflector Assembly Hitch AssemblyLeg Stand Assembly Refer to Figure 1-1 on pageTable of Contents Rear Deflector AssemblyDamaged drivelines could cause serious injury or death Section 1 Assembly and Set-UpRefer to Figure 1-5, Figure 1-6 and Figure Driveline InstallationChecking Driveline Minimum Length Refer to Figure 1-8 on pageSection 1 Assembly and Set-Up Checking Driveline Maximum LengthTable of Contents Refer to FigureSection 2 Operating General Notes for Field OperationsTransporting Operating Check ListTable of Contents ParkingOperating Instructions Section 2 OperatingRTR15 Tiller Hitch Sideshift Section 3 AdjustmentsRTR10 Tiller Hitch Offset Table of ContentsTable of Contents Drive ChainRear Deflector Section 3 AdjustmentsSection 3 Adjustments Skid Shoe AdjustmentTable of Contents Refer to FigureSection 4 Maintenance and Lubrication MaintenanceTine Replacement Driveline ProtectionTable of Contents Clutch Disassembly & ReassemblyRefer to Figure 4-3 View - B Section 4 Maintenance and LubricationStep Disassembly StepAssembly Step Table of ContentsTable of Contents StorageSection 4 Maintenance and Lubrication Driveline U-Joint LubricationLubrication Driveline ShaftTable of Contents Bearing On Right End Of Rotor ShaftGearbox Section 4 Maintenance and LubricationRTR15 Series Rotary Tiller Section 5 Speciﬁcations & CapacitiesRTR10 Series Rotary Tiller Table of ContentsFeatures Section 6 Features & BeneﬁtsTable of Contents RTR10 Series Rotary TillerSection 6 Features & Beneﬁts Table of ContentsRTR15 Series Rotary Tiller Solution Section 7 TroubleshootingProblem CauseSection 8 Appendix Torque Values ChartTable of Contents 5/05/06 Table of ContentsSection 8 Appendix Land PrideSection 8 Appendix WarrantyTable of Contents Overall Unit and Driveline One year Parts and LaborCorporate Ofﬁce P.O. Box Salina, Kansas 67402-5060 USA