GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always
be followed to reduce the risk of fire, electric shock and injury to persons,
including the following:
1.Read all instructions before using this Heater.
2.Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons.
3.Make certain that the power source conforms to the electrical requirements of the Heater.
4.Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the Heater is left operating unattended.
5.This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
6.DO NOT plug Heater into any other cord connected device, such as a power strip, surge protector, multiple outlet adapters or outlet-type air fresheners. The use of such devices may create a fire hazard. Plug unit directly into a 120V wall outlet only.
7.Avoid the use of extension cords because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, minimize the risk of overheating by ensuring that they are UL listed. The cord shall be a 3-wire, grounding type, with No. 14 AWG minimum size and rated not less than 1875 watts. NEVER use a single extension cord to operate more than one Heater.
8.Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, has been dropped or damaged in any manner. Return Heater to authorized service facility for examination, electrical or mechanical adjustment or repair.
9.To disconnect Heater, turn controls to OFF, then remove plug from outlet.
10.Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
WARNING: DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD.
11.Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
12.To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked.
13.Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so the Heater or other objects are not resting on it. Do not run Power Cord under carpeting. Do not cover Power Cord with throw rugs, runners, or the like. Arrange Power Cord away from room traffic and where it will not be tripped over.
14.This Heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.
15.A Heater has hot and arcing or sparking parts inside. Do not use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. It must NOT be used in potentially dangerous locations such as flammable, explosive, chemical- laden or wet atmospheres. This Heater is intended for general use ONLY.
16.This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate a Heater where it may fall into a bathtub or other water container.
17.Do not use Heater outdoors.
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.
FUNCIONAMIENTO
1.Cuidadosamente retire el Calefactor de la bolsa y de la caja.
2.Coloque el Calefactor sobre una superficie firme y plana. ADVERTENCIA: Los tacos de plástico o hule, tales como las patas de esta unidad, pueden pegarse a la superficie de los muebles y/o a los pisos de madera. La unidad podría dejar un residuo capaz de oscurecer, manchar o dejar marcas permanentes en el acabado de ciertas superficies de muebles, incluyendo superficies de madera y/o pisos de madera.
3.Conecte el cable eléctrico a un tomacorriente eléctrico de 120V~. Asegúrese que el enchufe encaje firmemente en el tomacorriente.
4.El Calefactor emitirá un “bip” cuando lo conecte por primera vez.
5.ENCIENDA el Calefactor oprimiendo el Botón de Encendido .
6.Al encender el Calefactor, la unidad estará en calor ALTO (1500 vatios) y mostrará la temperatura actual de la habitación (Figura 1)
7.Oprima el botón de Modo para calor BAJO (750 vatios).
8.Para APAGAR el Calefactor, presione el Botón de Encendido y desconecte el Calefactor del tomacorriente eléctrico.
T I M E R | M O D E | P O W E R | T E M P |
Figura 1 | | | |
TEMPORIZADOR: (Figura 2)
La función de temporizador puede ser activada cuando la pantalla del Calefactor está en cualquier velocidad o temperatura. Esta función le permite fijar la cantidad de tiempo que el Calefactor estará funcionando antes de apagarse automáticamente, de 1 hora a 7 horas. Presionar el Botón de Temporizador aumentará la cantidad de tiempo, en combinaciones de 1, 2 y 4 horas. Oprimir continuamente el botón provocará que el temporizador quede fijado para 7 horas. El Calefactor se apagará cuando el tiempo fijado haya transcurrido. La unidad puede volver a encenderse presionando el Botón de Encendido .
T I M E R M O D E
Figura 2
TERMOSTATO:
Oprimir el botón (
) o el botón (
) le permite a usted fijar la temperatura deseada del Calefactor. (Figura 3)
1.Oprima el botón (
) para aumentar la temperatura fijada deseada o presione el botón (
) para reducir la temperatura fijada deseada.
2.Cuando la temperatura del aire alcance los 2° por encima de la temperatura fijada, el Calefactor se apagará.
3.Cuando la temperatura del aire alcance un 1° por debajo de la temperatura fijada, el Calefactor se encenderá.
NOTA: Es normal que el Calefactor alterne entre ENCENDIDO y APAGADO para mantener la temperatura FIJADA.
T I M E R | M O D E | P O W E R | T E M P | IONIZER |
|
Figura 3 | | | | |
FUNCIÓN DE PERSIANA (LOUVER): (Figura 4)
Este Calefactor posee una persiana en la parrilla frontal superior que permite el ajuste vertical del flujo de aire. Deslice el control de la persiana hacia arriba o hacia abajo para ajustar el flujo de aire a voluntad.
Función De Persiana |
Figura 4 |
