Manuals / Lennox Hearth / Household Appliance / Stove

Lennox Hearth operation manual Epa Certified Catalytic Wood Burning Stove, MODEL 1003C

Models: 1003C

1 32

Download 32 pages 62.02 Kb

Page 1

Image 1

EPA CERTIFIED

CATALYTIC WOOD BURNING STOVE

RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE

INSTALLATION AND OPERATION

MANUAL

MODEL 1003C

THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. READ ENTIRE MANUAL THOROUGHLY BEFORE INSTALLATION.

P/N 775003M, Rev. P, 11/03

Page 1

Image 1

Lennox Hearth operation manual Epa Certified Catalytic Wood Burning Stove, P/N 775003M, Rev. P, 11/03, MODEL 1003C

Contents

RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE EPA CERTIFIED CATALYTIC WOOD BURNING STOVEP/N 775003M, Rev. P, 11/03 INSTALLATION AND OPERATION MANUAL17.SAVE THESE INSTRUCTIONS IMPORTANT WARNINGSTESTING/LISTING TABLE OF CONTENTSUSING THIS MANUAL EPA CERTIFICATIONWARNING: ELECTRICAL GROUNDING INSTRUC PLANNING YOUR INSTALLATIONSMOKE DETECTORS SELECTING A LOCATIONUSA REQUIREMENTS FLOOR PROTECTIONCANADA REQUIREMENTS STANDARD PARALLEL HEARTH PAD SHOWNCOMBUSTIBLE WALL CLEARANCES Corner Installation C 45 F Parallel InstallationA D B E PLANNING YOUR INSTALLATIONALCOVE CLEARANCES Alcove Dimension RequirementsAlcove Top View / Stove Clearances Alcove - Top View•WARNING: DO NOT INSTALL IN SLEEPING ROOM INSTALLATIONAIR INTAKE COVER OUTSIDE AIRSECURING THE STOVE TO THE FLOOR ACCEPTABLE CONNECTOR PIPE FOR INSTALLA- TIONSManufactured Mobile Homes Only GROUNDING STOVE Manufactured Mobile Homes OnlyVapor Barrier At Chimney Penetration CHIMNEY INSPECTIONCHIMNEY HEIGHT REQUIREMENTS The 2’ by 10’ Rule for Vent TerminationDRAFT REQUIREMENTS DRAFT TEST PROCEDUREINSTALLATION Connector Pipe. Not Approved For Using 6” 152 mm Diameter Single WallRESIDENTIAL STANDARD Manufactured Mobile HomesNOTES trationASH DRAWER CARE AND OPERATI0NCATALYTIC COMBUSTOR CATALYTIC BYPASS DAMPER CONTROLFUEL DOOR CARE AND OPERATIONGLASS BREAK-INPERIOD HOW TO START AND MAINTAIN A FIRECARE AND OPERATION CATALYTIC COMBUSTORWHY SEASONED WOOD? CATALYTIC TEMPERATURE PROBEFUEL REFUELINGCLEANING BLOWER INTAKE MAINTENANCEFUEL SEASONING GUIDEWARNING: THE GASKETS MUST BE KEPT IN GOOD DOOR / GLASS GASKET AND ASH DRAWER GAS- KETSERVICING GLASS Replacing GlassSide Cut-AwayView of Firebox CATALYST REPLACEMENTMAINTENANCE CATALYTIC COMBUSTORSMOKES OUT FUEL DOOR WHEN OPEN see TROUBLESHOOTINGDRAFT PROBLEMS: IF INSTALLING INTO A DOES NOT PRODUCE ENOUGH HEATCATALYST DEACTIVATION CATALYST PLUGGINGCATALYST SUBSTRATE CRACKING CATALYST SUBSTRATEOVERFIRING DAMAGE Overfiring Caused From Improper InstallationOverfiring Caused From Improper Operation Overfiring Caused From Improper FuelApprox. Weight SPECIFICATIONS: Model 1003CNote: Dimensions shown are approximations Maximum Log LengthITEM NO REPLACEMENT PARTS LIST: Model 1003CDESCRIPTION Door PartsModel Cat. NoDescription Part NoDamper Assembly COMPONENT DIAGRAMS - Model 1003CAir Intake Draft Module Door Assembly Handle Assembly P/N LB-102214 Nut Torque PlateOutside Air Floor Duct OAFD-S OPTIONAL ACCESSORIES - Model 1003CStove-StatKit SSK Blower Kit BK-100PAGE SAFETY/LISTING LABELPAGE EPA LABELOWNERSHIP RECORDS SERVICE AND MAINTENANCE LOG1110 West Taft Avenue Orange, CA