Lennox Hearth EBVI25, EBVI30US CAUTION Wear gloves and safety glasses for protection while doing required maintenance, Always verify proper operation after servicing., Turn off gas and electrical power before servicing the appliance., IMPORTANT Do not use abrasive cleaners on glass. Never clean the glass when it is hot.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 5

CAUTIONWear gloves and safety glasses for protection while doing

required maintenance.

IMPORTANT

Always verify proper operation after servicing.

WARNING

Turn off gas and electrical power before servicing the appliance.

OPERATION AND CARE OF YOUR

APPLIANCE

Appliance operation may be controlled

through a remotely located optional wall

thermostat or remote control.

In lieu of remote control or remote wall thermo-

stat operation, the appliance must be operated

directly through the off/on switch located on the

side surround panel (see Figure 4).

If your millivolt appliance is equipped with an

optional wall thermostat kit or remote control

kit and the pilot is lit (and valve is in the On

position), the appliance main burner may be

turned on and off with the wall thermostat

or remote control.

Always keep the appliance area clear and free

from combustible materials, gasoline and

other ﬂammable liquids.

Remember, millivolt appliances have a

continuous burning pilot ﬂame. Exercise

caution when using products with combus-

tible vapors.

MAINTENANCE

The appliance and venting system should be

thoroughly inspected before initial use and at

least annually by a qualiﬁed service technician.

However, more frequent periodic inspections

and cleanings should be performed by the

homeowner. Homeowner must contact a quali-

ﬁed service technician at once if any abnormal

condition is observed.

Refer to the maintenance schedule on Page

7 for maintenance tasks, procedures, recom-

mended frequency and by whom they should

be performed. Always verify proper operation

of the appliance after servicing.

Always turn off the gas and unplug the power

cord to the appliance before cleaning. Before

re-lighting, refer to the lighting instructions

in this manual. Instructions are also found on

pull-out panels located below the glass door in

the control compartment.

Keep lower control compar tment clean by

vacuuming or brushing at least twice a year.

More frequent cleaning may be required due to

excessive lint from carpeting, bedding materials,

etc. It is important that control compartments,

burners and circulating air passageways of the

appliance be kept clean.

Check Burner Flame Appearance

Visually check the ﬂame of the burner periodi-

cally making sure the ﬂames are steady and not

lifting or ﬂoating (see Figure 13 on Page 8).

Glass Cleaning

Note: Clean glass after ﬁrst two weeks of opera-

tion (after Burn-In period is over).

The viewing glass should be cleaned periodi-

cally to remove any build-ups caused from the

following:

• During start-up, it is normal for condensa-

tion to form on the inside of the glass (this

condensation and fog will usually disappear

in a few minutes). This can cause lint, dust

and other airborne particles to cling to the

glass surface.

• Initial curing of the high temperature paint

and burning off of lubricants used in the

manufacturing process may result in a ﬁlm

on the glass.

• A white coating may form on the glass as a

result of impurities and minerals in the fuel.

It is recommended that the glass be cleaned

two or three times during each heating season,

depending on the circumstances present.

Use one of the following to clean glass:

• Non-ammonia based household cleaner

• 50%-50% mix of white vinegar & water

• gas stove glass cleaner

WARNINGDo not attempt to touch the front enclosure glass with your hands while the ﬁreplace is in use. IMPORTANTDo not use abrasive cleaners on glass. Never clean the glass when it is hot.

Servicing Blower

To access the blower assembly for mainte-

nance, adjustment or replacement, see the

following procedure:

1. Unplug 120-volt A.C. power supply to

insert.

2. Shut off gas supply to insert.

3. Remove Glass Door (see Procedure

For Removing Standard Glass Door

Assembly on Page 8).

4. Remove log set, burner and grate.

5. Remove blower access panel and

gasket (see Figure 5 for model EBVI25

and Figure 6 for model EBVI30). Be

careful not to damage the gasket.

Access Panel

w/ Gasket

Figure 6

Model EBVI30

Figure 5

Access Panel

w/ Gasket

Model EBVI25

Remove 10 Screws (use phillips screwdriver)

Remove 12 Screws (use phillips screwdriver)