Lennox Hearth ELDV-35NE, ELDV-35NM, ELDV-35PM, ELDV-40NE, ELDV-40NM, ELDV-40PM, ELDV-45NE, ELDV-45NM, ELDV-45PM Figure 38 - , Step 5. WIRING - OPTIONAL FORCED AIR BLOWER KIT

25

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Note: Remote receiver should be located in the

wall, or if installed in the control compartment,

pulled all the way forward and completely to the

left or right against the corner posts. The door

must be removed ﬁrst to place the receiver in

the lower control compartment.

7. If wall-mounted ON/OFF control or thermo-

stat is to be used, mount it in a convenient

location on a wall near the ﬁreplace.

8. If an optional control is to be used, wire it in

the low voltage circuit as shown in Figure

37.

Note: The supplied 15 feet of 2 conductor wire

has one end of each conductor connected

to the gas valve circuit and the other end

of each conductor placed loose inside the

bottom compartment.

9. If the optional unit mounted (FRS) control

switch is installed, turn the appliance-

mounted ON/OFF burner control switch to

the OFF position.

10. After the wiring is complete, replace the

cover plate.

Note: No batteries to be installed in the battery

holder until a power outage, or if the appli-

ance is to be operated solely with two (2) "D"

batteries.

BLOWER CONTROL CIRCUIT WIRING

120V, 60HZ, 1PH

Factory Wired

Ground

Field Wired

Junction Box

Tab Intact

Tab

Broken

Plug blower

into this

receptacle

neerG - dnuorG

* Wall-mounted

ON/ OFF Blower

Switch or Variable

Speed Control Switch.

Blower

etihW - lar

t

ueN

120 VAC - Black

Green

Ground

Screw

White

Green

Neutral

Side of

Receptacle

Hot

Side of

Receptacle

Red

Black

Figure 38 - J-BOX WIRING

Step 5. WIRING - OPTIONAL FORCED AIR BLOWER KIT

Blower Access

Blower access is through the ﬁrebox bottom.

Remove the sub-ﬂoor, remove the burner and

remove ten screws securing the GTA assembly

to the ﬁrebox.

An electrical outlet box is provided for the

installation of the LBLK-100 forced air blower

kit. Electrical power must be provided to this

box to operate these blowers.

Install the blower kit according to the installation

instructions provided with the kit. Reposition

and reinstall the GTA assembly, burner and

sub-ﬂoor.

Contents

Main INSTALLATION INSTRUCTIONS ELDV Direct-Vent Gas Fireplaces WARNING /AVERTISSEMENT / AVISO Page Page Figure 2 - Table 2 Figure 1 - Table 3 Table 4 NEW YORK CITY, NEW YORK (MEA) COLD CLIMATE INSULATION MANUFACTURED HOME REQUIREMENTS Figure 3 - Typical Locations LOCATION Side Elevation View Vertical Vent Termination Clearances Figure 4 - Multiple Terminations VENT TERMINATION CLEARANCES Vertical Vent Termination Clearances EXTERIOR HORIZONTAL VENT TERMINATION CLEARANCE REQUIREMENTS A X Figure 7 Figure 9 - Figure 10 - MINIMUM CLEARANCES TO COMBUSTIBLES Appliance And Vent Clearances Table 6 Figure 8 - Figure 11 DETAILED INSTALLATION STEPS Figure 12 - Nailing Flanges Step 1. FRAMING TYPICAL INSTALLATION SEQUENCE FIREPLACE AND FRAMING SPECIFICATIONS FRONT VIEW TOP VIEW Inches (millimeters) 1/2 FIREPLACE FRAMING SPECIFICATIONS Figure 14 - Corner Framing with Horizontal Termination Figure 15 - Route Gas Line Table 7 Proper Sizing of Gas Line Step 3. INSTALL THE VENT SYSTEM General Information Figure 16 Figure 17 TRAHCHTGNELNOITCESTNEV Table 8 u Firestop/Spacer SV4.5L6/12/24/36/48 Vent Sections 40 Max (12.2 M) 1" (25.4 mm) Minimum Clearance to Combustibles u use Firestop/Spacer SF4.5VF 6 Min (1.8 M) Figure 19 Figure 18 Figure 20 Figure 21 Figure 22 - Roof Framing Figure 24 Figure 23 u WARNING Under no circumstances, may sepa- rate sections of concentric exible vent pipe be joined together. u v AELBAT BELBAT Figure 27 - Top Vent - THREE ELBOWS VERTICAL VENT FIGURES/TABLES u Figure 28 Figure 30 Figure 29 - HORIZONTAL VENT FIGURES/TABLES Notes: Figure 31 v ELBATC WARNING Figure 32 HORIZONTAL VENT FIGURES / TABLES (CONTINUED) ELBATD V v H H1 Wall Firestop/Spacer (SV4.5HF) ELBATE Figure 33 HORIZONTAL VENT FIGURES / TABLES (CONTINUED) SECuRE FLEx Figure 34 Figure 35 Step 4. FIELD WIRING Figure 37 CAUTION (In Canada, the current CSA C22-1 Canadian Electrical Code). Figure 38 - BLOWER CONTROL CIRCUIT WIRING 120V, 60HZ, 1PH Step 5. WIRING - OPTIONAL FORCED AIR BLOWER KIT Figure 40 Step 6. CONNECTING GAS LINE Flex Line Connector WARNING Never use an open ame to check for leaks. Figure 43 Step 7. VERIFYING APPLIANCE OPERA- TION Figure 42 Figure 41 Page ELDV3530 LOG PLACEMENT ELDV4035 LOG PLACEMENT Page Step 9. REMOVING AND INSTALLING THE GLASS DOOR Figure 49 Step 10. BURNER ADJUSTMENTS Flame Appearance and sooting Do not operate appliance with the glass front removed, cracked or broken. Page Step 11. HOOD INSTALLATION Figure 54 Figure 53 FINISHING REQUIREMENTS - Wall Details See Page 5 for Cold Climate Insulation and Page 8 for Clearances APPOSITION DES MISES EN GARDE RELATIVES LA SCURIT DUTILISATION Figure A Figure B Figure C COLOCACIN DE ADVERTENCIAS DE SEGURIDAD EN OPERACIN ATTACHING SAFETY-IN-OPERATION WARNINGS SAFETY LABEL DIAGRAMS DIAGRAMAS DE ETIQUETAS DE SEGURIDAD INSTALLATION ACCESSORIES Listed Secure Vent Components Cat. No. Model Description Cat. # Model Description Listed Secure Vent Components Cat. # Model Description Listed Secure Flex Components INSTALLATION ACCESSORIES CONTINUED * Page Figure 55 Millivolt Appliances Figure 56 Figure 59 Figure 57 Figure 58