Black Portion Of Frame
Not To Be Covered With
Combustible Materials
Wall
18”Covering
45°
1” |
|
Door |
|
Opening |
|
| Safe |
18” | Zone |
Be sure fireplace rests on a solid continuous floor or platform with appropriate framing for support and so that no cold air can enter the room from under the fireplace.
The fireplace may be positioned and then the framing built around it, or the framing may be constructed and the fireplace positioned into the opening.
Usually, no special floor support is needed for the fireplace, however, to be certain:
INSTALLING THE FIREPLACE
Step 1. Slide the fireplace into prepared fram- ing or position fireplace in its final position and frame later.
The fireplace may not be recessed into a com- bustible floor. Maintain the floor to hearth clearance established by the fireplace lower front face.
Figure 5
DO NOT permanently place furniture or other items such as decorative pillows within 60" of the fireplace front face.
ASSEMBLY STEPS
Note: The following steps represent the normal sequence of installation. Each installation is unique, however, and might require a different sequence.
1. Estimate the total weight of the fireplace |
system including chimney and surround ma- |
terials such as brick, stone, etc., to be in- |
stalled. Shipping weights for the fireplace may |
be found on page 18. |
2. Measure the square footage of the floor |
space to be occupied by the system, surrounds |
and hearth extensions. |
3. Note the floor construction, i.e. 2 x 6’s, 2 x 8’s |
or 2 x 10’s, single or double joists, type and |
thickness of floor boards. |
Combustible
Wall
Maintain 1/2" (13mm) Air Space at Sides and Back
1/2" (13mm)
Metal Safety Strip
Hearth
Extension
Floor
1.Position firebox prior to framing or into prepared framing.
2.Install the chimney system.
3.Install optional outside combustion air kit.
4.Plumb gas line if a decorative gas appliance will be used. (Gas connections should only be performed by an experienced, licensed/certi- fied tradesman.)
5.Complete the installation, finish wall mate- rial, surround and hearth extension to your individual taste.
6.Assemble and attach optional glass door assembly.
Study the three dimensional illustration (Fig- ure 1 ) to get a general idea of each element of your fireplace system.
PRE-INSTALLATION NOTES
The fireplace may be installed directly on a combustible floor or raised on a platform of an appropriate height. Do not place fireplace on carpeting, vinyl or other soft floor coverings. It may, however, be placed on flat wood, ply- wood, particle board or other hard surfaces.
4. Use this information and consult your local |
building code to determine if you need addi- |
tional support. |
CAUTION: DO NOT BLOCK THE
If you plan to raise the fireplace and hearth extension, build the platform assembly then position fireplace and hearth extension on top. Secure the platform to the floor to prevent possible shifting.
CLEARANCES
Minimum clearance to combustibles for the fireplace is as follows; sides and back – 1/2" (13mm), combustible floor – 0" (0mm), adja- cent wall 18" (457mm), adjacent shielded wall (K factor of .84 or less 40" W x 40" H ) 12" (305mm), ceiling –
Note: Clearance at the nailing flange for both fireplace models is 0" (0mm).
Note: Adjacent wall considerations are for an adjacent wall on only a single side. Walls should not be placed at minimum distance at both sides of the fireplace.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Figure 6
Combustible
Wall
Maintain 1/2" (13mm) Air Space at Sides and Back
Hearth Extension
1/2" (13mm)
Metal Safety Strip | Platform | Floor |
Figure 7
Step 2. Insert the provided metal safety strips, beneath the fireplace as illustrated (Figures 6, 7 and 8 ). The safety strips should overlap 1/2" min. for continual coverage of the floor.
Note: Safety strips are not required when fire- place rests on a noncombustible surface.
Note: Install the hearth extension only as illus- trated (see Figures 43 and 44).
5
