41
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.A. This appliance has a pilot which must be lighted by a piezo
igniter. When lighting the pilot, follow these instructions
exactly.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
• Do not tr y to light any appliance.
• Do not touch any electric switch; do not use any phone in your
building.
1. STOP! Read the safety information above on this label.
2. (If applic able) Set the thermostat to lo west setti ng. Turn wall on /off
switch, unit mounted on/off switch or remote control switch "OFF."
3. Turn OFF all electric power to the appliance.
4. Access the control compartment.
5. Push in gas control knob slightly and turn clockwise to "OFF."
NOTE: Knob cannot be turned from "PILOT" to "OF F" unles s knob is
pushed in slightly. Do Not force.
6. Wait five (5) minutes to clear out any gas. Then smell for gas,
including ne ar the floor. If you smell gas , STOP! Follow "B" in the
safety information above on this label. If you don't smell gas, go to the
next step.
7. Find pilot - located in firebox on the same plane as the top of the burner.
8. Turn knob on gas control counterclockwise to "PILOT."
9. Push in control knob all the way and hold in. Immediately light the pilot
.sthgil tolip litnu )nottub eht gnihsup( retingi ozeip eht gnireggirt yb
Continue to hold the control knob in for about 1-1/2 minutes after the
pilot is lit. Release knob and it will pop back up. Pilot should remain
lit. If it goes out, repeat steps 5 through 9.
• If knob does not pop up when released, stop and immediately call
your service technician or gas supplier.
LIGHTING INSTRUCTIONS
TO TURN OFF GAS TO APPLIANCE
• If the pilot will not stay lit after several tries, turn the gas control
knob to "OFF" and call your service technician or gas supplier.
10. Turn gas control knob counterclockwise to "ON."
11. Close control compartment.
12. (If applicable) Turn on all electrical power to the appliance.
13. (If applicable) Set thermostat to desired setting. Turn wall on/off switch,
unit mounted on/off switch or remote control switch "ON."
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don’t try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
4. Push in gas control knob slightly and turn clockwise to "OFF." Do
not force.
5. Close the main line gas shut-off valve.
6. Close control compartment.
Pilot Assemblies
H
I
L
O
W
TPTH TP TH
P
I
L
O
T
P
I
L
O
T
O
N
it
O
F
F
OUT
IN
LO
HI
IN OUT
OFF
PILOT
ON
PILOT
O
N
O
F
F
P
I
L
O
T
L
O
H
I
Gas Control Valves
SIT
Robertshaw
Gas Control Knobs
Honeywell
P/N 62L2901
1. (If applica ble) Set the thermosta t to lowest setting. Turn wall on /off
switch, unit mounted on/off switch or remote control switch "OFF."
2. Turn OFF all ele ctric po wer to the ap plianc e, if servi ce is to be
performed.
3. Access the control compartment.