LG Electronics 2 manual Editing Content, Number of characters, font size, font type

			Using LG EzSign 2.0 Editor	7
Editing Content		ꔈꔈ	Editable areas (photo, text, photo and text
			group) are displayed to the left; to the right,
			property settings which you can additionally set
		ꔈꔈ	for the selected area are displayed.
			Each area -such as a photo or photo and text
			group -has two property sets. The two property
			sets will be displayed in turn when a content file
			is played. In this case, you can select the follow-
			ing options: 1) Configure the time to the right
			when the content file is displayed. 2) Select one
			image area from the two areas below. What you
		ꔈꔈ	select on the right is displayed on the left.
			If a photo is bigger than the image area, its
			aspect ratio is automatically adjusted, resulting
		ꔈꔈ	in degrading the picture quality.
			If two images which are the same are added to
NOTE		ꔈꔈ	both areas, image-sticking may occur.
			For the font area, the input length may vary
ꔈꔈ	The file formats supported for images are GIF,	ꔈꔈ	depending on the font size.
ꔈꔈ	JPEG, PNG, and BMP.		If the entered text exceeds the maximum
	Selected GIF or BMP files are automatically		length of the input box without the Flow Speed
	converted to JPEG files before being shown.		function enabled, the text will be truncated
	The conversion may decrease the image quality	ꔈꔈ	when the content is displayed on TV.
ꔈꔈ	depending on the quality of the original file.		You can only enter a limited amount of text.
	4-bit BMP files are not recommended due to		(Up to 2700 pixels). If the entered text exceeds
ꔈꔈ	poor quality.		the maximum length, the text input will be lim-
	Images larger than 4095 pixels in width or	ꔈꔈ	ited.
ꔈꔈ	height are not allowed.		The following elements affect the text length.
	If you upload a single image or two of the		Number of characters, font size, font type,
	same image to the editing zone, you cannot	ꔈꔈ	bold/italic properties
	switch the image over. Do not display static		When a font is installed in the system, it is also
	images on the screen for long periods of time.		added to the Editor and displayed in the font
ꔈꔈ	This can cause image sticking.		list. It is recommended that you install the gen-
	Uploading photos saved in the Network folder	ꔈꔈ	eral TTF (True Type Font).
	to the photo area may not work, depending on		Depending on the font type or system environ-
	the network settings. If an error occurs, upload		ment, some characters cannot be displayed or
	the photos after copying them to the local PC.		will be displayed as □ while others can be dis-
			played but without formatting. If this happens,
			you will need to select an existing font or install
			a new font which supports these characters so
		ꔈꔈ	that they can be displayed properly.
			Setting the input direction, also determines the
			text flow. When the direction is set from left to
			right, the text flows to the right whereas, if it is
			set to the opposite direction, the text flows to
		ꔈꔈ	the left.
			You can modify the text properties to the right;
		ꔈꔈ	you can edit text to the left.
			If you use the same color as the Panel Saver
			content text font, image-sticking may occur. It
		ꔈꔈ	is recommended to use a different color.
			In the left area, you can edit the text which
			appears when an image is selected in the right
		ꔈꔈ	area.
			If the content file being edited is not in the
			playlist, it is automatically added when you click
			the NEXT button.