LG Electronics 42LC2R Adjustment Instruction, PCB assembly adjustment items, LP62x, Edid Data

ADJUSTMENT INSTRUCTION

1. Application Range

This spec. sheet is applied to all of the LP62A/B/C chassis(H3-High) manufactured at LG TV Plant all over the world.

2.Specification

2.1Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help to protect test instruments.

2.2Adjustment must be done in the correct sequence.

2.3The adjustment must be performed at 25±5°C temperature and 65±10% relative humidity if there is no specified designation.

2.4The input voltage of the receiver must be kept between 100~220V, 50/60Hz.

2.5Before adjustment, execute Heat-Run for 30 minutes at RF no signal

3.Adjustment items

3.1PCB assembly adjustment items

•Channel memory

-Download the channel data from BOM to EEPROM by using LGIDS.

•Option adjustment following BOM

-Tool Option1

-Tool Option2

-Area Option

LP62x

Cortez Version	x.xx
Panel Used XX hr.
Tool Option1	7
Tool Option2	161
Area Option	16
:
:

(Fig. 1)

1)Push the ADJ key in the Adjust Remocon.

2)Input the Option Number that was specified in the BOM, into the Shipping area.

3)Select "Tool Option1/ Tool Option2/ Area Option" by using /(CH+/-) key , and press the number key(0~9)

consecutively

ex) If the value of Tool Option1 is 7, input the data using number key "7" (Fig. 1)

3.2 SET assembly adjustment items

•Auto AV(ZH-AV3, TH-AV1) Color Balance

•Aging (by Power on key)

•Adjustment of White Balance

•Auto Component Color Balance adjustment

-Standard equipment : MSPG925FA

•Auto RGB Color Balance adjustment

-Standard equipment : MSPG925FA

4. EDID

Caution

*Use the proper signal cable for EDID Download

-Analog EDID : Pin3 exists

-Digital EDID : Pin3 exists

=> Caution: - Never connect HDMI & DVI-D & DVI-A Cable at the same time.

-Use the proper cables below for EDID Writing

4.1EDID Data

4.1.1.ANALOG(256 Bytes )

•BLOCK1 (128BYTE)

	00		01	02	03	04	05	06	07	08	09	0A	0B		0C	0D	0E	0F
00	00		FF	FF	FF	FF	FF	FF	00	1E	6D	a				b
10	c			01	03	01	46	27	78	EA	D9	B0	A3		57	49	9C	25
20	11		49	4B	A5	6E	80	31	40	01	01	01		01	45	40	01	01
30	61		40	01	01	01	01	1B	21	50	A0	51		00	1E	30	48	88
40	35		00	BC	88	21	00	00	1C	4E	1F	00		80	51	00	1E	30
50	40		80	37	00	BC	88	21	00	00	18	00		00	00	FD	00	38
60	4B	1F		3D	09	00	0A	20	20	20	20	20		20		d
70								d									00	99

4.1.2.HDMI(256 Bytes )

•BLOCK1 (128BYTE)

00	01 02 03 04 05 06 07	08	09 0A		0B 0C	0D	0E	0F
00 00	FF FF FF FF FF FF 00	1E 6D		a		b

10c 01 03 80 46 27 78 EA D9 B0 A3 57 49 9C 25

2011 49 4B A5 6E 80 31 40 01 01 01 01 45 40 01 01

3061 40 01 01 01 01 1B 21 50 A0 51 00 1E 30 48 88

4035 00 BC 88 21 00 00 1C 4E 1F 00 80 51 00 1E 30

50	40	80	37	00	BC 88		21	00	00	18					d
60						d								00		00	00	FD
70	00	38	4B	1F	3D	09	00	0A	20	20	20	20		20		20	01	14
		BLOCK2 (128BYTE)
	00	01	02	03	04	05	06	07	08	09	0A	0B		0C		0D	0E	0F
00	02	03	24	F1	49	85	04	02	01	03	11		12	13		14	23	09
10	07	07	23	09	07	07	23	09	07	07	83		01	00		00	65	03
20	0C	00	10	00	01	1D	00	80	51	D0	1C		20	40		80	35	00
30	BC	88	21	00	00	1E	8C	0A	D0	8A	20	E0		2D		10	10	3E
40	96	00	13	8E	21	00	00	18	2A	12	00		10	41		43	17	20
50	28	60	35	00	00	00	32	00	00	1C	01	1D		80		18	71	1C
60	16	20	58	2C	25	00	C4	8E	21	00	00	9E		00		00	00	00
70	00	00	00	00	00	00	00	00	00	00	00		00	00		00	00	6B

=> Detail EDID Options are below (a, b, c, d, e) a. Product ID

Model Name	Product ID		Product ID
		Dec		Hex	EDID table
37LC2R	30059(A)	30059		756B	6B75
	30060(D)	30060		756C	6C75
42LC2R	40023(A)	40023		9C57	579C
	40024(D)	40024		9C58	589C
b. Serial No : Controlled on production line
c. Month, Year : Controlled on production line:
	ex) Montly : '03' => '03'
	Year	: '2005' =>		'0F'

- 11 -