- 12 -
d. Model Name/Monitor Name:
e. Checksum: Changeable by total EDID data
5. ADC Calibration

5.1 Adjustment of RF/AV/S-VIDEO

* Required Equipments
•Remote controller for adjustment
•802F Pattern Generator, Master (MSPG-925FA), etc.
•MSPG-925FA Pattern Generator
(Which has Video Signal: 100% Color Bar Pattern
shown in Fig. 1)
=> Model : 202 / Pattern: 33 (PAL : ZH, TH)
Model : 201 / Pattern : 33 (NTSC : MH)
(Fig. 1)
5.1.1 Method of Auto RF/AV/S-VIDEO Color Balance.
1) Press the FRONT-AV KEY on R/C for converting input
mode.
2) Input the Video Signal: 100% Color Bar signal into
AV3(ZH), AV1(TH), VIDEO1(MH)
3) Set the PSM to Standard mode in the Picture menu.
4) Press INSTART key on R/C for adjustment.
5) Press the (Vol.+) key to operate the set, then it becomes
automatically
6) Auto-RGB OK means the adjustment is completed
5.1.2 Requirement
•This AV color balance adjustment should be performed
before White Balance Adjustment.
•After color balance adjustment, You must push "power on"
key. ("Power on" key is "Access Heat_run mode")

5.2 Adjustment of Component.

* Required Equipments
•Remote controller for adjustment
•802F Pattern Generator, Master (MSPG-925FA), etc.
•MSPG-925FA Pattern Generator
(Which has 720p YPbPr signal : 100% Color Bar
Pattern shown in Fig. 2 )
=> Model: 217 / Pattern: 33
•It is very import to use correct adjustment pattern like
Fig. 2.
- Within the pattern, color sequence should be aligned
: W-Y-C-G-M-R-BLUE-BLACK
(If color sequence is reversed (Black -> ... -> White),
reverse the pattern with REV key, when using
Master pattern generator like MSPG-925)
- If Minimum Black Level and/or Maximum White
Level is not correct, Do select 100% Color Bar
Pattern.
(Fig. 2)
5.2.1 Method of Auto Component Color Balance
1) Input the Component 720p 100% Color Bar(MSPG-925FA
model:217, pattern:33) signal into Component.
(ZH : component , TH/MH : component 1 or 2)
2) Set the PSM to Standard mode in the Picture menu.
3) Press the INSTART key on R/C for adjustment.
4) Press the (Vol. +) key to operate the set , then it
becomes automatically.
5) Auto-RGB OK means the adjustment is completed.

5.3 Adjustment of RGB

* Required Equipments
•Remote controller for adjustment
•802F Pattern Generator, Master (MSPG-925FA), etc.
•MSPG-925FA Pattern Generator
(Which has XGA [1024x768] 60Hz PC Format output
signal : 100% Color Bar Pattern shown in Fig. 3 )
•It is very import to use correct adjustment pattern like
Fig. 10.
- Within the pattern, color sequence should be aligned
: W-Y-C-G-M-R-BLUE-BLACK
(If color sequence is reversed (Black ->...-> White),
reverse the pattern with REV key, when using
Master pattern generator like MSPG-925)
- If Minimum Black Level and/or Maximum White
Level is not correct, Do select 100% Color Bar
Pattern.
(Fig. 3)
5.3.1 Method of Auto RGB Color Balance
1) Input the PC 1024x768@60Hz 1/2 Black&White Pattern
(MSPG-925FA model:3, pattern:33) into RGB.
2) Set the PSM to Standard mode in Picture menu.
3) Press the INSTART key on R/C for adjustment.
4) Press the (Vol. +) key operate To set , then it becomes
automatically.
5) Auto-RGB OK means adjustment is completed.
Model Name
37LC2R-TH 00 00 00 FC 00 33 37 4C 43 32 52 2D 54 48 0A 20 20 20
42LC2R-TH 00 00 00 FC 00 34 32 4C 43 32 52 2D 54 48 0A 20 20 20