Life Fitness 701 manual FACTOR525 PEC DEC ATT. Assemblyinstructions LEVEL1

701 FACTOR525 PEC DEC ATT. ASSEMBLYINSTRUCTIONS (LEVEL1)

NOTE: IF THE SHROUDIS ASSEMBLEDTO THE FACI'OR 525, IT WILL NEEDTO BE REPdOVED

TO ASSEMBLE THE PEG DEC ATTACHMENT.PLEASE REMOVETHE SHROUD AT THIS TIME BY CAREFULLYREMOVINGTIIE FOURTEEN(14) SHROUDFASTENEFKg.

o

Insert two (2) 2 IN. SQ. ENDCAPSinto both ends of the BEARINGHOUSING,as shown on drawing.

SECURELYassemble the BEARINGHOUSINGand the CENTERPULLEYBRACKETto the FRONTUPRIGHTas shown on drawing, using p, vo (2) I/'2 X 4-1/2 IN. BOLTS,four (4) I~ WASHERS,and two (2) I/2. IN. LOCKNUTS. (TttE CONNECTORPLATES ON THE BEARING HOUSING AND THE CENTER PULLEY BRACKET HAVE SLOTTED HOLES. SHIFT THE BEARING HOUSING DOWNAND THE CENTER PULLEY BRACKET UP AS FAR AS POSSIBLE)

¢°

Insert four (4) 2 IN. SQ. ENDCAPSinto BOTHENDSof the LEFT, and RIGHTPECDECARMS shown on drawing.

Assemble one (1) 3/4 IN: WASHER,and the LEFT ARM.a DVANCEto the LEFT PEC DECARM shown on drawing. Also Assembleone (1) 3/4 IN. WASIl['2t~., :,,td the RIGHTARMADVANCEto the RIGHT PEC DEC ARMas shown.

Insert four (4) 3/4 IN. FLANGEBEARINGSinto {he BUSHINGSof the BEARINGHOUSING, shown on drawing.

Insert the LEFT and RIGHTPECDECARMSthrough the 3/4 IN. FLANGEBEARINGSin the BEARINGHOUSINGon their respective sides as shown on drawing, ~d SECUREthem in place with two (2) 3/d I.D. STARLOCKCOLLARS.

Slide two (2) 4 X 12 ROLLERPADSonto the LEFT and RIGHTPEC DECARMS,until the ROLLERPAD is FLUSHwith the bottom or'the ARMS. (IF A LUBRICANTIS REQUIRED,COAT THE INSIDE OF THE ROLLER PAD WITII RUBIJINC ALCOIIOL. ALSO, ROTATING THE PAD WHILE PUSHING UP ',VILL I lELP TO EASE ASSEMBLY)

Assemble t~vo (2) KNOBSto two (2) COTTERLESSHITCHPINS as shown on drawing. Insert the

(2)co'r-FERLESS HITCHPINS through the BUSHINGSon the CAMSof the RIGHTand LEFT PEC DEC ARMS,and into the holes on the PEC ARMADVANCESSEE. DRAWING.

Attach two (2) CAP.RIAGEGUll)US to the CA~I STOPo,~ the IIEARINGI1OUSINGwhere the ARMADVANCESmakes contact with the CANt STOP.

10.LOOSELYassemble txvo (2) 4-1/2_ X IN. PU LLEYS and ~wo (2 ) CABLE RETAINING CLIPS to the CENTERPULLEYBRACKETas shown on drawing, using two (2) 3/8 X 2 IN. BOLTS,four (4) 3/8 WASHERS,and two (2) 3/8 IN. LOCKNUTS. (NOTE: THIS CONNECTIONWILL TIGHTENED AFTER THE CABLE ttAS BEEN ROUTED)

THIS CONCLUDES THE ASSFMBLY OF (LEVEL