19
MODELS 95SI, 93S, 90S STAIRCLIMBERS
TOOLS REQUIRED:Metric Hex Key Set, Side Cutters
NOTE: Proceed with the following steps before attaching the DISPLAYCONSOLE and ACCESSORY TRAY as
described in the Assembly Instructions.
1. Locate the REMOTE CONTROL(a). Configure the REMOTE CONTROL for a VERTI-
CAL (C-V) installation. Secure the REMOTE CONTROL to the top of the HANDLEBAR
(15) as shown. Be sure the CABLE TIES (C-V) are pulled tight and trim the excess
CABLE TIES.
2. Loop the REMOTE CABLE (b) under the HANDLEBAR (15) and secure it to the top of the
CONSOLE EXTENSION TUBE (F) using one CABLE TIE (c) at the location shown.
3. Locate the SPACER (d). With the SPACER oriented as shown, feed all the previously
removed CONSOLE CONNECTORS, POWER CORD, and COAXIAL CABLE through the
large center hole in the SPACER. Slide the SPACER onto the CONSOLE MOUNTING
PLATE (D) making sure the top of the SPACER hooks over the top of the CONSOLE
MOUNTING PLATE. Align the mounting holes of the SPACER and CONSOLE MOUNTING PLATE. Run the
POWER CORD, and COAXIAL CABLE through the channel at the top of the SPACER.
4. Locate the MOUNTING BRACKET(e). With the MOUNTING BRACKET
oriented as shown, feed all the CONSOLE CONNECTORS through the
large center hole in the MOUNTING BRACKET. Align the LOCATING
TABS (f) of the MOUNTING BRACKETwith the tab slots and position
the MOUNTING BRACKET into the center channel of the SPACER (d).
Slide the MOUNTING BRACKET upward until it locks solidly in the
SPACER. Secure the MOUNTING BRACKETto the SPACER using
two FLATHEAD SCREWS (g). Tighten the SCREWS securely.
5. Install the DISPLAYCONSOLE (9) as instructed in the Assembly
Instructions using the four new 1-1/2" SCREWS supplied. Tighten the
SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS.
CAUTION: Do not pinch any wires when assembling the DISPLAY
CONSOLE (9) to the CONSOLE MOUNTING PLATE (D).
6. Attach the ADAPTER BRACKET(AA) to the ENTERTAINMENT
CONSOLE (h) to the using four SCREWS (BB). Tighten the
SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS.
Attach the ENTERTAINMENTCONSOLE to the UPPER MOUNT-
ING PLATE (j) using four SCREWS (k) and WASHERS (m).
Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the
SCREWS.
7. Connect the COAXIALCABLE, POWER CORD and REMOTE CABLE
(b) to the rear of the ENTERTAINMENTCONSOLE (h) as shown under
Console Cable Connections at the end of this manual.
8. CABLE TIE(c) any excess cable together behind the ENTERTAINMENT CON-
SOLE (h) and position the cables between the MOUNTING BRACKET (e) and
the DISPLAYCONSOLE (9).
9. Secure thePOWER ADAPTER (n) to the FRONT STABILIZER (o) using two
CABLE TIES (c) as shown. Be sure the CABLE TIES are pulled tight and
trim the excess CABLE TIES. Connect the screw-type connector of the
POWER CORD (p) to the underside receptacle. Bundle excess power cord
and store under the unit. Connect the COAXIAL CABLE (q) to the broadcast
supply cable in similar fashion.
10. Connect the POWER SUPPLY CORD to the POWER ADAPTER (n).
11. Continue with the remainder of assembly as instructed in the Assembly Instructions.
Plug the POWER SUPPLYCORD into an electrical outlet upon completion.