21
MODELS 91TI, 90T TREADMILLS

TOOLS REQUIRED: Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters

NOTE: Proceed with the following steps immediately after attaching the DISPLAYCONSOLE as described in the Assembly

Instructions. Do not install the ACCESSORYTRAYS or PUSH RIVETS.

1. Remove the nine SCREWS (a) from the rear of the console securing the FRONTCONSOLE
(b) to the REAR CONSOLE (c). Carefully lift the FRONTCONSOLE. Set the FRONT CON-
SOLE and SCREWS aside.
2. Route the main wire harness (D), POWER CORD (d), and COAXIAL CABLE
(e) through the LARGE CABLE CLIP (f) located at the left inside of the
REAR CONSOLE (c). Route the POWER CORD and COAXIAL
CABLE through the LARGE CABLE CLIP (f) located at the center
inside of the REAR CONSOLE. Continue routing the POWER
CORD and COAXIAL CABLE through the notch at the top of the
REAR CONSOLE.
3. Locate the REMOTE CONTROL (g). Configure the REMOTE CON-
TROL for a VERTICAL (C-V) installation. Secure the REMOTE
CONTROLto the left end of the ERGO CROSSBAR (13) as shown.
Be sure the CABLE TIES (C-V) are pulled tight and trim the excess
CABLE TIES.
4. Route the REMOTE CABLE (h) along the LEFT HANDLEBAR (1). Secure
the REMOTE CABLE using two CABLE TIES (j) at the locations shown. Be
sure the CABLE TIES are pulled tight and trim the excess CABLE TIES. Route
the remaining REMOTE CABLE through the CABLE CLIP (k) located on the bot-
tom left of the REAR CONSOLE (c) and up through the LEFT ACCESS PANEL.
Route the REMOTE CABLE through the LARGE CABLE CLIP (f) located at the center
inside of the REAR CONSOLE. Continue routing the REMOTE CABLE through the notch at the
top of the REAR CONSOLE.
5. Connect the MAIN WIRE HARNESS (D) and HANDLEBAR WIRE HARNESS (B) to the back of
the FRONT CONSOLE (b). With the POWER CORD (d), COAXIAL CABLE (e) and REMOTE
CABLE (h) oriented in the TOPCONSOLE NOTCH as shown, secure the FRONT CONSOLE (b)
using the nine previously removed SCREWS (a). Tighten the SCREWSsecurely. Replace the ACCESS
PANELS (C).
NOTE: Be careful not to pinch the REMOTE CABLE (h) when replacing the ACCESS PANELS (C).
6. Install the ACCESSORYTRAYS (17 & 18) as instructed in the Assembly Instructions.
7. Remove the LEFT and RIGHTUPPER HANDLEBAR ENDCAPS (m) and discard them.
8. Position the BRACKET TUBE (n) as shown and slide the ends into the
HANDRAILS (1 & 2) until fully seated.
9. Install the four SET SCREWS (o) into the BRACKETTUBE MOUNT-
ING ARMS (p) and tighten the SETSCREWS securely. Do not over-
tighten the SETSCREWS.
10. Attach the ENTERTAINMENTCONSOLE (q) to the UPPER MOUNT-
ING PLATE (r) using four SCREWS (s) and NYLON WASHERS (t).
Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS.
11. Connect the COAXIAL CABLE (e), REMOTE CABLE (h), and POWER
CORD (d) to the rear of the ENTERTAINMENT CONSOLE (q) as shown
under Console Cable Connections at the end of this manual.
12. Unwrap the MAIN WIRE HARNESS (D) located at the base of the LEFT
UPRIGHT (1). Route the MAIN WIRE HARNESS, POWER CABLE and COAX-
IALCABLE under the CROSS FRAME MEMBER (E). Connect the 10-PIN
CONNECTOR(10P) of the MAIN WIRE HARNESS to the corresponding JACK
(F) locates at the top of the CONTROLBOARD (G).