Life Fitness CLSXH manual 10 a

IMPORTANT!

DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS. ALL NECESSARY COMPONENTS NEEDED

TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.

IMPORTANT!

NE JETEZ PAS LE KIT PLACÉ SUR LE DESSUS DES LEVIERS DE PÉDALE. IL CONTIENT TOUS LES ÉLÉMENTS

NÉCESSAIRES POUR L'INSTALLATION.

1. Locate the LEFT HANDLEBAR (11). Position the HANDLEBAR near the top

of the LEFT PIVOT ARM (A).

If equipped with Lifepulse, connect the 2-PIN HEART RATE CONNECTOR

(B) leading from the HANDLEBAR to the 2-PIN CONNECTOR (C) extending

from the top of the LEFT PIVOT ARM. Carefully slide the excess HEART

RATE CABLE into the top of the LEFT PIVOT ARM.

9

11

Align the mounting holes of the LEFT HANDLEBAR with the mounting holes at the top of the LEFT PIVOT ARM. Secure them together using three SCREWS (1).

NOTE: BE CAREFUL NOT TO PINCH THE HEART RATE CABLE WHEN SECURING THE LEFT HANDLEBAR TO THE LEFT PIVOT ARM.

2.	Locate one LEFT FRONT ROCKER COVER (5) and the LEFT BACK
	ROCKER COVER (6). Position the LEFT BACK ROCKER COVER over the
	user side of the ROCKER ARM making sure that it seats fully over the
	BULLHORN MOUNTING BRACKET (D). Place the FRONT ROCKER
	COVER over the opposite side of the ROCKER ARM in the same manner.
	Secure the COVERS using two PHILLIPS PAN HEAD SCREWS (2).
	Tighten the SCREWS securely. Do not over-tighten the SCREWS.
3.	Locate one FRONT PIVOT ARM COVER (9) and one BACK PIVOT ARM
	COVER (10). Position the BACK PIVOT ARM COVER over the user side of
	the ROCKER ARM making sure that it interlocks with the ROCKER COVER.
	Place the FRONT PIVOT ARM COVER over the opposite side of the PIVOT
	ARM in the same manner. Secure the COVERS using two PHILLIPS PAN
	HEAD SCREWS (2). Tighten the SCREWS securely. Do not over-tighten the
	SCREWS.
4.	Locate the LEFT BULLHORN (13). Secure the BULLHORN to the
	BULLHORN MOUNTING BRACKET (D) using two FLAT HEAD SCREWS
	(1). Tighten the SCREWS securely. Locate and attach the LEFT
	BULLHORN COVER (15) to the base of the BULLHORN using one SCREW
	(22). Tighten the SCREW securely. Do not over-tighten the SCREW. Slide
	the GASKET (E) downward to meet the BULLHORN COVER.
5.	Repeat steps one through four to install the RIGHT ROCKER COVERS (5 &
	6), PIVOT ARM COVERS (9 & 10), BULLHORN (14) and BULLHORN
	COVER (16).
	NOTE: THE RIGHT PIVOT ARM COVERS ARE REVERSED FRONT
	AND BACK. THE SCREWS WILL BE INSTALLED FROM THE REAR.
6.	Unwrap the MAIN WIRE and HEART RATE HARNESS (F & G) leading from
	the MONOCOLUMN (H). Feed the WIRE HARNESSES through the
	CONSOLE SUPPORT ASSEMBLY TUBE (I) located at the top and front of
	the MONOCOLUMN. Locate the CONSOLE SUPPORT ASSEMBLY (7) and
	position it near the top of the MONOCOLUMN. Feed the WIRE

B C

2

1

10 A

5

D

A

E 6

2 13

1

15 22

F G

HARNESSES through the CONSOLE SUPPORT ASSEMBLY as shown.

Align the bottom mounting holes of the CONSOLE SUPPORT ASSEMBLY

with those in the CONSOLE SUPPORT ASSEMBLY TUBE. Secure them

together using six SCREWS (1). Tighten the SCREWS securely.

NOTE: BE CAREFUL NOT TO DAMAGE THE WIRE HARNESSES (E &

F) WHEN ROUTING IT THROUGH THE CONSOLE SUPPORT

ASSEMBLY OR WHEN MOUNTING THE CONSOLE SUPPORT

ASSEMBLY TO THE CONSOLE SUPPORT ASSEMBLY TUBE.

7. Locate the ACCESSORY TRAY (17). Slide the ACCESSORY TRAY into the

top of the MONOCOLUMN (H) as shown. Be sure the ACCESSORY TRAY

is fully seated.

NOTE: BE CAREFUL NOT TO DAMAGE THE MAIN WIRE HARNESS

WHEN SLIDING THE ACCESSORY TRAY INTO THE MONOCOLUMN.

Secure the accessory tray to the CONSOLE SUPPORT ASSEMBLY using

two SCREWS (3). Tighten the SCREWS securely. Do not over-tighten the

SCREWS.

21 2 7

2

1

83

1

I

4

17

H