Life Fitness UT4, RT4 user manual Assembling the Recumbent Exercise Bike

ASSEMBLING THE RECUMBENT

EXERCISE BIKE

Tools Required: Metric Wrench Set, Metric Allen Wrench Set, Phillips Screwdriver

1.1. Locate and install the two LEVELER FEET (A) to the bottom of the REAR STABILIZER (B).

2.Attach the REAR STABILIZER (B) to the BASE UNIT

(C) using two 2-3/8" BUTTON HEAD SCREWS (1) from the top of the REAR STABILIZER BRACKET (D) and two 13/16" BUTTON HEAD SCREWS (2) from the front side of the REAR STABILIZER BRACKET. Tighten the SCREWS securely.

3.Locate the HANDLEBAR ASSEMBLY (E) and the SEAT ASSEMBLY (F). With the handlebars facing upward and forward, align the mounting holes of the HANDLEBAR ASSEMBLY with those in the SEAT ASSEMBLY. Secure the HANDLEBAR ASSEMBLY to the SEAT ASSEMBLY using four 5/8" BUTTON HEAD SCREWS (3) and FLAT WASHERS (4). Tighten the SCREWS securely.

4.Locate the SEAT BOTTOM (G). Align the SEAT BOT- TOM mounting holes with those in the LOWER SEAT SUPPORT TUBES (H). Secure the SEAT BOTTOM using four 2" PHILLIPS SCREWS (5) and LOCK WASHERS (6). Tighten the SCREWS securely.

5.Align the guide rollers located on the underside of the SEAT ASSEMBLY (F) with the SEAT EXTRUSION (J). Carefully guide the SEAT ASSEMBLY onto the SEAT EXTRUSION. Slide the SEAT ASSEMBLY fully for- ward.

6.In the hole located in the user right side of the SEAT EXTRUSION (J), behind SEAT ASSEMBLY (F), install one 1-3/8" BUTTON HEAD SCREW with locktite (7), one 15/16" FLAT WASHER (8), and one 1" RUBBER BUMPER (9) as shown.

7.Mount the SEAT ADJUSTMENT LEVER (K) to the user right side of the SEAT ASSEMBLY (F) using two 3/4" PHILLIPS SCREWS (10) and LOCK WASHERS (11). Tighten the SCREWS securely.

8.Secure the SEAT BACK (L) to the UPPER SEAT SUP- PORT TUBES (M) using four 2" PHILLIPS SCREWS

(5) and LOCK WASHERS (6). Tighten the SCREWS securely.

9.Locate the SEAT EXTRUSION ENDCAP (N). Secure the SEAT EXTRUSION ENDCAP to the SEAT EXTRU- SION (J) using two 1/2" PHILLIPS SCREWS (12).

10.Locate the MONOCOLUMN (O). Insert the WIRE (P) leading from the SIDE ACCESS HOLE (Q) of the MONOCOLUMN fully into the MONOCOLUMN. Remove the GROMMET (R) from the SIDE ACCESS HOLE and set it aside.

11.Slide the MONOCOLUMN COVER (S) onto the MONOCOLUMN (O) as shown. Slide the MONOCOL- UMN COVER up to the HANDLEBAR TUBE (T).

12.Re-insert the GROMMET (R) into the SIDE ACCESS HOLE (Q) of the MONOCOLUMN (O). Pull the WIRE

(P) back out through the SIDE ACCESS HOLE.

13.With the HANDLEBAR TUBE (T) facing the rear of the unit as shown, slide the MONOCOLUMN (O) into the MONOCOLUMN BRACKET (U) of the BASE UNIT (C). Slide the MONOCOLUMN down until it is fully seated. Secure the MONOCOLUMN to the MONOCOLUMN BRACKET using two 3-15/16" HEX HEAD BOLTS (13) and three LOCK WASHERS (14) (as shown) from the front side of the MONOCOLUMN and two 2-3/8" HEX HEAD BOLTS (15) and LOCK WASHERS (14) from the user left side of the MONOCOLUMN BRACKET. Tighten the BOLTS securely.

CAUTION: BE CAREFUL NOT TO PINCH THE WIRE (V) LEADING FROM THE MONOCOLUMN BRACKET (U) WHEN INSERTING THE MONO- COLUMN (O) INTO THE MONOCOLUMN BRACKET.

14.Connect the WIRE (V) leading from the MONOCOL- UMN BRACKET (U) to the corresponding WIRE (P) from the SIDE ACCESS HOLE (Q) of the MONOCOL- UMN (O). Slide the MONOCOLUMN COVER (S) downward to the meet the MAIN SHROUDS (W). Secure the MONOCOLUMN COVER to the MAIN SHROUDS using four 1/2" PHILLIPS SCREWS (12) and matching FLAT WASHERS (6). Tighten the SCREWS securely. Do not overtighten the SCREWS.

15.Remove the DISPLAY CONSOLE (X) from its shipping carton. Position the above the DISPLAY CONSOLE BRACKET (Y). Connect the WIRE (Z) leading from the DISPLAY CONSOLE BRACKET to the corresponding JACK(s) located on the back of the DISPLAY CON- SOLE. Secure the DISPLAY CONSOLE to the DIS- PLAY CONSOLE BRACKET using four 1/2" PHILLIPS SCREWS (12). Tighten the SCREWS securely. Do not overtighten the SCREWS.

16.Locate the PEDALS. Install the RIGHT PEDAL (AA) (marked with an "R") to the USER RIGHT CRANK ARM (BB). Repeat for the LEFT PEDAL (CC) (marked with an "L").

NOTE: THE LEFT PEDAL (CC) HAS REVERSE THREADS.

17.Locate the WATER BOTTLE BRACKET (DD). Secure the WATER BOTTLE BRACKET to the underside of the MONOCOLUMN (O) using two 3/8" PHILLIPS SCREWS (16). Tighten the screws securely. Insert the WATER BOTTLE (EE) into the WATER BOTTLE BRACKET.

18.Position the unit in the desired location for use. The unit can be easily moved into place by lifting the rear of the unit and rolling it on the front rollers. Level the unit before use. Refer to the leveling instructions stated in the operations portion of this manual.

7