Life Fitness UT4 Assembling The Upright Exercise Bike, Note The Left Pedal Y Has Reverse Threads

ASSEMBLING THE UPRIGHT EXERCISE BIKE

Tools Required: Metric Wrench Set, Metric Allen Wrench Set, Phillips Screwdriver

1.Locate and install the two LEVELER FEET (A) to the bottom of the REAR STABILIZER (B).

2.Attach the REAR STABILIZER (B) to the BASE UNIT

(C)using two 2-3/8" BUTTON HEAD SCREWS (1) from the top of the REAR STABILIZER BRACKET (D) and two 13/16" BUTTON HEAD SCREWS (2) from the front side of the REAR STABILIZER BRACKET. Tighten the SCREWS securely.

3.Locate the MONOCOLUMN (E). Insert the WIRE (F) leading from the SIDE ACCESS HOLE (G) of the MONOCOLUMN fully into the MONOCOLUMN. Remove the GROMMET (H) from the SIDE ACCESS HOLE and set it aside.

4.Slide the MONOCOLUMN COVER (J) onto the MONOCOLUMN (E) as shown. Slide the MONOCOL- UMN COVER up to the HANDLEBAR TUBE (K).

5.Re-insert the GROMMET (H) into the SIDE ACCESS HOLE (G) of the MONOCOLUMN (E). Pull the WIRE

(F)back out through the SIDE ACCESS HOLE.

6.With the HANDLEBAR TUBE (K) facing the rear of the unit as shown, slide the MONOCOLUMN (E) into the MONOCOLUMN BRACKET (L) of the BASE UNIT (C). Slide the MONOCOLUMN down until it is fully seated. Secure the MONOCOLUMN to the MONOCOLUMN BRACKET using two 3-15/16" HEX HEAD BOLTS (3) and three LOCK WASHERS (4) (as shown) from the rear side of the MONOCOLUMN and two 2-3/8" HEX HEAD BOLTS (5) and LOCK WASHERS (4) from the user left side of the MONOCOLUMN BRACKET. Tighten the BOLTS securely.

CAUTION: BE CAREFUL NOT TO PINCH THE WIRE (M) LEADING FROM THE MONOCOLUMN BRACKET (L) WHEN INSERTING THE MONO- COLUMN (E) INTO THE MONOCOLUMN BRACKET.

7.Connect the WIRE (M) leading from the MONOCOL- UMN BRACKET (L) to the corresponding WIRE (F) from the SIDE ACCESS HOLE (G) of the MONOCOL- UMN (E). Slide the MONOCOLUMN COVER (J) downward to the meet the MAIN SHROUDS (N). Secure the MONOCOLUMN COVER to the MAIN SHROUDS using four 1/2" PHILLIPS SCREWS (6) and matching FLAT WASHERS (7). Tighten the SCREWS securely. Do not overtighten the SCREWS.

8.Locate the SEAT POST CAP (O). With the curved side facing upward toward the SEAT (P), slide the SEAT POST CAP over the SEAT POST (Q).

9.Locate and slide the SEAT POST SPACER (R) over the end of the SEAT POST (Q). Using two 1/4" PHILLIPS SCREWS (8), secure the SEAT POST SPACER to the end of the SEAT POST. Tighten the SCREWS securely.

10.With the nose of the SEAT (P) facing forward, insert the SEAT POST (Q) into the SEAT POST SUPPORT

(S).

11.Begin inserting the SEAT ADJUSTMENT KNOB (T). Lift upward on the seat and seat post until the seat post locks into a position. Insert the 5/16" PHILLIPS LOCKING SCREW (9) and tighten securely.

12.Slide the SEAT POST CAP (O) downward to meet the top of the SEAT POST SUPPORT (S). Secure the SEAT POST CAP to the SEAT POST SUPPORT using two 1/2" PHILLIPS SCREWS (6). Tighten the SCREWS securely. Do not overtighten the SCREWS.

13.Remove the DISPLAY CONSOLE (U) from its shipping carton. Position the above the DISPLAY CONSOLE BRACKET (V). Connect the CONNECTOR (W) lead- ing from the DISPLAY CONSOLE BRACKET to the corresponding jack located on the back of the DIS- PLAY CONSOLE. Secure the DISPLAY CONSOLE to the DISPLAY CONSOLE BRACKET using four 1/2" PHILLIPS SCREWS (6). Tighten the SCREWS securely. Do not overtighten the SCREWS.

14.Locate the HANDLEBAR ASSEMBLY (X). With the handlebars facing forward, position the HANDLEBAR ASSEMBLY near the top of the HANDLEBAR TUBE

(K). Slide the HANDLEBAR ASSEMBLY fully into the HANDLEBAR TUBE. Secure the HANDLEBAR ASSEMBLY to the HANDLEBAR TUBE using four 5/8" BUTTON HEAD SCREWS (10) and matching FLAT WASHERS (11). Tighten the SCREWS securely.

15.Locate the PEDALS. Install the RIGHT PEDAL (Y) (marked with an "R") to the USER RIGHT CRANK ARM (Z). Repeat for the LEFT PEDAL (AA) (marked with an "L").

NOTE: THE LEFT PEDAL (Y) HAS REVERSE THREADS.

16.Locate the WATER BOTTLE BRACKET (BB). Secure the WATER BOTTLE BRACKET to the underside of the HANDLEBAR TUBE (K) using two 3/8" PHILLIPS SCREWS (12). Tighten the screws securely. Insert the WATER BOTTLE (CC) into the WATER BOTTLE BRACKET.

17.Position the unit in the desired location for use. The unit can be easily moved into place by lifting the rear of the unit and rolling it on the front rollers. Level the unit before use. Refer to the leveling instructions stat- ed in the operations portion of this manual.

5