Installing Mod Light

(Fig. 48)

(Fig. 50)

(Fig. 52)

(Fig. 49)

(Fig. 51)

(Fig. 53)

Installing Sunray Mod Light (Optional)

1.Identify the appropriate parts in the Titan mounting kit included with the Mod Light.

2.Titan Kit includes the following.

Hex screw, split washer, metal washer, 1/2” hexogonal base piece, and hex key.

3.Place the hex screw through the split washer and metal washer.

4.Place both the hex screw and both metal washers together through the round end of the base piece (Fig. 51).

5.Place the base assembly over the accessory hole of the Titan.

6.Orient the base piece so the hexogonal shape of the base piece matches the hexogonal detail of the Titan and so the hex screw rests on top of the accessory mount.

7.Tighten the entire assembly by tightening the hex screw into the Tetra’s accessory hole

8.Then snap Mod Light and arm assembly on the base (Fig. 52).

Installing the Pointer Light (Optional)

1.Identify the appropriate parts in the Titan Modeling Light Kit.

2.Kit includes the following.

Hex screw, 1/4” base piece, Infinity arm, modeling light and light bracket.

3.Position the base piece details on the detail of the Titan’s accessory hole.

4.Place the hex screw through the base piece and tighten with hex key (Fig. 53).

5.Place Infinity arm with holder over the base piece and press firmly down until the Infinity arm snaps into position (Fig. 54).

6.Place Modeling light in to light bracket.

Replacing ROC Handle Batteries

The battery life of your ROC Handles will vary depending on usage and technique. But eventually the handle batteries will exhaust.

The handles will signal when the battery power is becoming low. The handle LED will blink eight times after any button is pressed.This is a signal to change the batteries prior to the next dive.

Replacing the handle batteries is an easy procedure. However, pay special attention to the wear of the O-ring and to the orientation of the batteries.You will need to purchase the ROC Handle O-ring battery kit (P/N 802-0117)

1.Using a 3/32 hex key, remove the two hex screws on the back of the handle (Fig. 55).

2.Remove the Handle Cap from the handle assembly.

3.Remove old batteries from handle board.

4.Install new 1/3 N batteries into the handle board (Fig. 56)

5.Service Handle Cap O-ring or replace with a new O-ring.

6.Press the Handle Cap into the handle assembly so O-ring seals evenly.

7.Replace both hex screws in Handle Cap and tighten using hex key.

ROC Handle O-ring and Battery Kit (part # 802-0117)

Kit contains one O-ring, 3/32 hex key, and two batteries for one ROC Handle.

(Fig. 54)

D100 specifications

The Light & Motion D100 is an exceptional dive light designed to meet the needs of underwater enthusiasts, offering a blend of durability, performance, and versatility. This powerful dive light is particularly favored by scuba divers, underwater photographers, and videographers who require high-quality illumination in the challenging underwater environment.

One of the standout features of the D100 is its impressive output of up to 1000 lumens, providing bright and even light that penetrates the depths of the ocean. The beam angle of 80 degrees ensures that divers can illuminate a wide area, making it ideal for exploring coral reefs or wrecks where peripheral visibility is essential.

The D100 is built with robust construction, featuring an aluminum body that is lightweight yet highly durable. This ensures that the light can withstand the rigors of marine environments, including resistance to corrosion from saltwater. The anodized finish adds an extra layer of protection against scratches and impacts, further enhancing its longevity.

In terms of battery technology, the D100 is equipped with a rechargeable lithium-ion battery that guarantees hours of use on a single charge. The intelligent battery management system allows for real-time tracking of battery life, providing divers with peace of mind by ensuring they have adequate light throughout their dive. The light also features a simple user interface with three brightness levels, enabling divers to easily adjust the output based on their specific needs.

The Light & Motion D100 is also designed to minimize environmental impact. It uses LED technology, which not only extends the life of the light but also consumes less energy compared to traditional lighting solutions. This efficiency translates to fewer battery changes and less waste over time.

Moreover, the D100 is designed for versatility, with a built-in mounting system that allows it to be easily attached to various camera systems and dive gear. This makes it an excellent choice for underwater photographers who require flexible lighting options.

In conclusion, the Light & Motion D100 blends innovative technology with exceptional performance, making it a top choice for divers and underwater photographers alike. With its robust construction, impressive lumen output, and efficient battery system, the D100 delivers reliable illumination for every underwater adventure. Whether you are exploring marine life or capturing stunning underwater images, the D100 stands out as a reliable companion in the depths.

Light & Motion D100 manual Installing Mod Light, Replacing ROC Handle Batteries

Models: D100