READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:1004ICV

B1204 Page 2 of 4

2. WIRE-IN (Fig. B)

NON-METALLIC

J-BOX COVER

Open hinged J-BOX COVER fully to its locked position (lift

SHEATHED CABLE

 

slightly to unlock).

(12 OR 14 GAUGE ONLY)

 

 

 

Open hinged KNOCK OUT to allow NON-METALLIC CABLE

 

 

to enter JUNCTION BOX. Push CABLE through CLAMP.

 

 

Note: Wiring and connections must not be placed in JUNCTION

 

 

BOX in a manner which will interfere with the CLAMPS

 

 

action to provide strain relief.

 

 

Wire to SUPPLY LEADS. WHITE FIXTURE LEAD to NEUTRAL

HINGED KNOCK OUT

 

SUPPLY LEAD. BLACK FIXTURE LEAD to HOT (120V) SUPPLY

CABLE CLAMP

 

LEAD. BARE FIXTURE WIRE to SUPPLY GROUND. Use wirenuts

 

JUNCTION BOX

(local hardware item). Place all electrical connections in the

 

 

 

J-BOX and close the J-BOX COVER.

 

 

3.SWING-UP (Fig. C)

Extend MOUNTING BAR to reach opposite joist and fasten in place. Adjust fixture to desired position along MOUNTING BAR and lock in place using locking screw.

4.CLOSE-IN (Fig. D)

Install plasterboard or other dry type ceiling. Hole in board can be cut either on the floor or after the board is secured to the ceiling using MOUNTING FRAME opening as cutting guide. Make sure ROTO-CLIPS are rotated out of hole area to be cut, also making sure that socket and wiring are positioned away from hole area. Roto Clips can only be rotated counter- clockwise. This detail allows easy removal of reflector trim by rotating TRIM counterclockwise and permits installing Reflector Trim tightly against the ceiling surface by rotating trim clockwise after pushing Trim into ceiling.

5.AIRSEAL® INSTALLATION (optional)

Install a bead of silicone caulking compound between the ceiling opening and edge of HOUSING. Housings are tested in accordance with ASTM E 283 (max 2 cfm @ 75 pa) and comply with WSEC & MEC when installed as instructed.

LOCKING SCREW

DEFORM MATERIAL AT

ANY CORNER OF FRAME

FOR ADDITIONAL LOCK

IF NEEDED

6.SNAP-ON (Fig. E)

Important - Insert SOCKET CUP in neck of REFLECTOR making sure SPRING TABS fully engage into SLOTS in REFLECTOR.

7.PUSH-UP (Fig. F)

Push REFLECTOR TRIM straight up until it is tight against ceiling.

}SEE SEPARATE REFLECTOR TRIM INSTRUCTION SHEETS

U.S. AND FOREIGN PATENTS PENDING

®LIGHTOLIER a GENLYTE company. 631 Airport Road, Fall River, MA 02720

Page 1 Page 3
Page 2
Image 2
Lightolier 1004ICVN instruction sheet B1204 Page 2, Airseal Installation optional
Page 1 Page 3

1004ICVN specifications

Lightolier 1004ICVN is a highly versatile and efficient recessed lighting fixture designed to meet a variety of residential and commercial needs. Known for its compact design and innovative features, this product stands out in the world of illumination solutions.

One of the main features of the Lightolier 1004ICVN is its insulation contact rating. The fixture is designed to be installed in ceilings with direct contact with insulation, allowing for greater flexibility in your lighting layout. This makes it an ideal choice for new construction or remodels where a clean, flush look is desired while maintaining compliance with energy efficiency codes.

The fixture is equipped with a robust, high-efficiency reflector that enhances the quality of light output and minimizes glare. This reflector uses advanced lighting technologies to produce an even light distribution, making it ideal for various settings, from living rooms to commercial spaces. The smooth finish of the reflector also aids in maintaining a contemporary aesthetic, blending seamlessly into modern architectural designs.

Another important characteristic of the Lightolier 1004ICVN is its compatibility with a range of light sources, including LED, incandescent, and compact fluorescent bulbs. This flexibility means that users can choose the best lighting solution that meets their specific requirements for brightness and color temperature. The fixture's design also allows for easy bulb replacement, a feature that enhances its practicality and convenience.

The Lightolier 1004ICVN is designed with user-friendly installation features. It includes adjustable hanger bars that facilitate mounting in various ceiling types and ensure a secure fit. This makes the installation process straightforward, even for those who are not lighting professionals.

Moreover, the fixture supports dimming capabilities, allowing users to create the desired ambiance in any space. This is increasingly important as homeowners and businesses look to enhance their environments through controllable lighting solutions.

In summary, the Lightolier 1004ICVN is a forward-thinking recessed lighting solution that combines a sleek design with versatile functionalities. Its compatibility with various light sources, insulation contact rating, light-enhancing reflector, and ease of installation make it a popular choice for both residential and commercial applications. With the growing emphasis on energy efficiency and customizable lighting experiences, the Lightolier 1004ICVN effectively meets the demands of modern lighting projects.
Top Page Image Contents