Lightolier A-16 manual Module Ordering Information, Features, Labels, Finish, Mountings

						Lighting Systems A-16
1BHF  PG 				"MFSPOÜ 4FSJFT   -JHIU 5 1FS h DN 4FDUJPO
			3		2
			1			5	3-5/16”
							(8.41cm)
				2-3/16”			NOT TO SCALE
				(5.56cm)
			8-1/16” (20.48cm)
Module Ordering Information
Family	Series	Track	Length	Shielding	Lamps	Finish	Options
A	2	B		D
		A = Track	4 = 4-Foot	A = Solid	28 = 28w	WH = White	E1 = Emergency Pack, 120v
		B = No Track	8 = 8-Foot	B = Perf	54 = 54w	AL = Aluminum	E2 = Emergency Pack, 277v
			12 = 12-Foot	C = Pierce			D1 = Dimming 120v
				D = Lens			D2 = Dimming 277v
Complete ordering instructions below.							X5 = 5 Through Wires

Features

1.Housing: Extruded aluminum housing in lengths of 4’ (121.92cm), 8’ (243.84cm) and 12’ (365.76cm). There are no exposed fasteners. The end caps are die-cast aluminum sculpted and finished to match the housing.

2.Reflectors: Extruded aluminum brite dipped anodized, kick reflector and die-formed high purity anodized specular aluminum.

3.Lamping: One T5 28W or 54W lamp per four-foot nominal length. Provided by others.

4.Alignment Mechanism: The housing and the end cap each have a draw tight mechanism that creates a hairline joint along and at the ends of the run. To operate the mechanism, the installer tightens two screws.

5.Shielding: Extruded acrylic lens. 26% opaque. Textured white finish.

Labels

UL, cUL and I.B.E.W.

Finish

Powder coated baked white or silver enamel.

Custom colors available, consult factory.

Mountings

All mounting is on 48” (121.92cm), 96” (243.84cm) and 144” (365.76cm) centers.

Cable Suspension (not shown) 4-1/2" (11.43cm) diameter flat canopy finished white enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36" (91.44cm) and adjustable cable gripper. Cable mounting at the ends of a run is not available when track is being used. Installing stems at the ends of the run will prevent the fixture from hanging off center caused by the weight of the track fixture. Cable suspension can be used in the center of runs that have track installed. Consult factory for other options.

Stem Mounting (not shown) - 4-1/2" (11.43cm) diameter flat canopy, 1/4"

(0.64cm) IP (1/2” (1.27cm) OD) stem. The stem can accommodate up to 2-12 gauge and 3-18 gauge solid wires. All components have a white finish.

Electrical

Ballast is <10% THD, 1.0 ballast factor, program start. Color-coded quick connectors allow ease of connection for joiner modules. For special circuiting consult factory. Factory installed ballast disconnect allows the ballast to be disconnected from and reconnected to incoming power under load without turning the entire circtuit off.

Dimming: 120/277 VAC 1% dimming level, 4 or 5 wire feed required.

Emergency Battery Pack: 28 watt: 520 lumens @ 90 minutes, 54 watt: 700 lumens @ 90 minutes.

Ordering Instructions

Individual Fixtures:

1.Order number of MODULES required.

2.Order one POWER FEED END SET per MODULE.

Continuous Rows:

1.Determine run length.

2.Order the appropriate number of MODULES for the complete run.

3.Order one POWER FEED END SET per run.

4.Order one INTERMEDIATE SUSPENSION per MODULE minus one per run.

5.For runs that exceed amperage limits, order the appropriate number of

INTERMEDIATE POWER FEEDS.

Job Information Type:

Job Name:

Cat. No.:

Lamp(s):

Notes:


"JSQPSU
3PBE
'BMM
3JWFS
."

t


t
'BY



We reserve the right to change details of design, materials and finish.

XXXMJHIUPMJFSDPN
½

1IJMJQT
(SPVQ
t $