Lightolier C6T6A-MHT6RF manual Trim Kit + Flood Upper Reflector Frame-In Kit Lamp, Features

Calculite® HID Adjustable Accent C6T6A-MHT6RF

Page 1 of 2 6" Aperture, T6 Ceramic Metal Halide, Flood

19-1/8" 15"

20" to 30"

19-5/8"

10-5/8"

20-1/4" (Electronic)

22-1/8" (Magnetic)

Top View

Flood Upper

Reflector

Ceiling Cutout: 6 9/16" (167mm) Dia.

For Complete Fixture Order: Trim Kit + Upper Reflector (MHT6RF) + Frame-In Kit. Each Sold Separately.

Trim Kit + Flood Upper Reflector			Frame-In Kit		Lamp
C6T6A		+ MHT6RF (Flood Upper Reflector)	C6A39T6E1	Electronic 120V	39W T6	Ceramic MH
	CLW	Specular Clear, White Painted Flange	C6A39T6E2	Electronic 277V	39W T6	Ceramic MH
	CLP	Specular Clear, Matching Flange	C6A70T6E1	Electronic 120V	70W T6	Ceramic MH
	CCDW	Comfort Clear Diffuse, White Painted Flange	C6A70T6E2	Electronic 277V	70W T6	Ceramic MH
	CCDP	Comfort Clear Diffuse, Matching Flange	C6A15T6E1	Electronic 120V	150W T6	Ceramic MH
	CCZW	Champagne Bronze, White Painted Flange	C6A15T6E2	Electronic 277V	150W T6	Ceramic MH
	CCZP	Champagne Bronze, Matching Flange		Magnetic 120V/277V	150W T6	Ceramic MH

Features

1.Flood Upper Reflector: Specular textured aluminum; provides 40° beam. Interchangeable with 12° Spot (MHT6RS) and 25° Narrow Flood (MHT6RNF); see spec sheets C6T6A-MHT6RS and C6T6A-MHT6RNF.

2.Trim Kit:: Low brightness aperture cone; anodized aluminum, self-flanged in painted white or aperture-matching polished flange. Consult factory for other finishes.

3.Lamp Shield: High-temperature glass as required by code; captive during re-lamping.

4.Trim Kit Adjustment Mechanism: Provides 40° vertical tilt, 360° horizon- tal rotation; lockable. Patented EZ-Aim Helical Drive System provides fast and accurate hot aiming with Philips screwdriver.

5.Socket Housing: Galvanized steel, pre-wired with G12 pulse rated socket. Snaps onto yoke for secure attachment without tools; unitized construction assures proper alignment of lamp to optics for consistent optical perfor- mance.

6.Frame Housing: Steel, 0.029" (22-Ga.), matte black finish. Removable cover for top re-lamping.

7.Frame Vertical Adjustment Mechanism: Accommodates mounting to vir- tually any ceiling system using pre-installed mounting bars, or 1/2" EMT tub- ing (by others). Single locking feature secures all adjustments. Alignment holes and markings allow fixture to be pre-set prior to installation. Final adjustment can be made from below from inside fixture.

8.Mounting Bars: Galvanized steel, 0.048" (18-ga.), pre-installed telescoping bars extend to 30" long and lock securely into position. Built-in locking tabs provide positive attachment to common T-bar systems. Self-centering feature simplifies installation in 24" O.C. grid systems. Attaches to steel or wood joists without accessories.

9.Retention Springs: Rust resistant springs secure trim for quick, tool-less installation.

10.Ballast / Cover Assembly: Accessible from below and removable without tools for inspection and ballast replacement .

11.Junction Box: 0.059" (16-ga.) galvanized steel. UL listed for 8 No. 12 AWG, 90°C through branch circuit conductors. Allows inspection from below.

12.Accessory Holder: (Not Shown) Sold separately catalog # CAH6; die- formed steel, matte black finish, slide-in installation. Accepts up to two 4 3/4" dia. media.

13.Thermal Protector: (Not Shown) Meets NEC and UL requirements. Do not install insulation above nor within 3" (76mm) of any part of the luminaire.

Electrical

Electronic Ballast: 120V or 277V, 50/60 Hz., encased, high power factor, T.H.D <15%, thermally and transient protected, RMI/RFI complies with FCC Part 18 on- consumer equipment, shut-down circuit at end of lamp life, sound rating “A”, -5°F (-20°F for 150W) minimum starting temperature, Type 1 outdoor rating. *150W Magnetic Ballast: 120V/277V dual voltage, 60 Hz., encased and potted, HX-HPF circuit type, high power factor, sound rating “B”, -20° F minimum starting temperature, Type 1 Outdoor rating.

Ballast		ANSI Code	Voltage	Max. Amps	Input Watts
39W MH		M130	120/277	0.39/0.17	44
70W MH		M139	120/277	0.67/0.28	78
150W	MH	M142	120/277	1.40/0.60	167
* 150W	MH	M142	120/277	3.70/1.60	180

Options and Accessories

Chicago Plenum: Consult Factory

Fuse (magnetic ballast): Add suffix F1 or F2 to Frame-In Kit (F1=120V, F2=277V)

Labels

UL (Suitable for Damp Locations), CSA, I.B.E.W.

For 150W, install fixtures with minimum spacing between:

1.		Center-to-center of adjacent luminaries: 2 feet.
2.		Top of luminaire to overhead building member: 1/2 inch.
3.		Luminaire center to side building member: 1 foot.
	Job Information		Type:
	Job Name:
	Cat. No.:
	Lamp(s):
	Notes:

Lightolier a Genlyte companywww.lightolier.com 631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710 We reserve the right to change details of design, materials and finish.

© 2006 Genlyte Group LLC • B0406