Lightolier IS FAEM3, LIGHTOLIER a GENLYTE THOMAS company, New Installation, C0506

INSTRUCTION SHEET NO.

IS:FAEM3

C0506 Page 2 of 4

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

NEW INSTALLATION

A. INSTALLING EMERGENCY BALLAST TO STANDARD FRAME-IN KIT (Fig. 1 and 8).

1.Before placing FRAME-IN KIT in the ceiling, install EMERGENCY BALLAST to the center of MOUNTING FRAME BRACKET as shown.

2.Tighten SCREW to secure two units together.

3.Remove JUNCTION BOX COVER and appropriate J-Box K.O., then attach

EMERGENCY BALLAST BX CONNECTOR.

WIRING - Read and understand all instructions before proceeding.

•Make sure AC power is off at the fuse box.

•Regular ballast and emergency ballast must be fed from the same branch circuit.

•Be sure all electrical connections are made and junction box is closed before connecting inverter connectors in switch/indicator light box.

•In switched fixtures, emergency ballast must be connected ahead of any local switching.

•Emergency ballast is shipped from the factory ready for 120V or 277V supply connection. Line Voltage selecton is made at switch box. For 120V, remove wire nut from 120V lead (black) and connect to black lead of test switch, then cap the 277V lead (orange).

B.INSTRUCTIONS FOR WIRING EMERGENCY BALLAST FOR (1) OR (2) 4-PIN LAMPS ELECTRONIC A.C. BALLAST FRAME-IN KIT

1.Before converting to emergency lighting, please identify no. of lamps and wattage of frame-in kit, then select appropriate Wiring Diagram A, B or C for rewiring. There is a requirement to remove lamp leads from A.C. ballast, and reconnect to emergency ballast.

2.Disconnect either BLUE LAMP LEAD from BALLAST by inserting conductor of RED JUMPER (provided) into open terminal of QUICK CONNECTOR of BALLAST as shown in Fig. 2. Gently pull BLUE LAMP LEAD out. Then remove RED JUMPER for later use.

3.Repeat step 2 (above) to remove other BLUE LAMP LEAD, and one appropriate RED OR YELLOW LAMP LEAD from BALLAST (Fig. 2) and wiring diagrams.

4.Insert appropriate RED OR YELLOW JUMPER into the terminal where the RED

OR YELLOW LAMP LEAD was previously removed from QUICK CONNECTOR (Fig. 3).

5.Follow WIRING DIAGRAM A, or B, or C to complete the wiring at FLEX “A”.

Fig. 1

	FRAME-IN KIT		EMERGENCY
			BALLAST
	BX
			MOUNTING
CONNECTOR
				FRAME
				BRACKET
	J-BOX			SWITCH/
				INDICATOR
	COVER			BRACKET
		SOCKET		SCREW
		CUP

Fig. 2

	BLUE LAMP	INSERT
	LEADS	RED
		JUMPER
RED LAMP
LEADS
		QUICK
		CONNECTOR

Fig. 3

RED INSERT

JUMPER

QUICK

CONNECTOR

WIRING DIAGRAM A (1-LAMP FIXTURE) (1 LAMP EMERGENCY)

NOTE: FOR UNSWITCHED CIRCUIT, CONNECT
BOTH WHITE/RED AND ORANGE/BLACK LEADS					UNSWITCHED		COMMON
IN JUNCTION BOX TO UNSWITHCHED 120V					120V OR
						277V	(NETURAL)	GROUND
OR 277V. VOLTAGE SELECTION IS MADE IN									For dimming ballast, connect
SWITCH BOX.									dimming leads to dimmer
					WALL		WHITE*	GREEN
					SWITCH
		BLK 120V						WHITE
								WHT / BLK
	BLACK
TEST					WHT / RED
		ORG 277V
SWITCH
					ORG / BLK
	BLACK	ORG/BLK
			EMERGENCY
								B	W G
			BALLAST		WHITE
		RED							ELECTRONIC
			FLEX	FLEX	WHT/BLK			A.C. BALLAST
	INVERTER		"B"	"A"	BLUE/WHT
	CONNECTOR				BLUE
	WHITE				RED				Y Y R R
	BROWN -				YEL/BLK
CHARGE					YEL			B	B
LIGHT
	VIOLET +
								RED*
				JUNCTION
	SWITCH BOX							RED
				BOX
	STAB-IN CONNECTOR (2 CONDUCTORS)				BLUE** BLUE**	RED**	RED
	STAB-IN CONNECTOR (3 CONDUCTORS)
	* WHITE AND RED JUMPERS PROVIDED							LAMPHOLDER
** (2) BLUE AND (1) RED LEADS REMOVED
	FROM ELECTRONIC BALLAST

WIRING DIAGRAM B (2-LAMP FIXTURE) UP TO 2-42W

(1 LAMP EMERGENCY)

NOTE: FOR UNSWITCHED CIRCUIT, CONNECT

BOTH WHITE/RED AND ORANGE/BLACK LEADS UNSWITCHED

IN JUNCTION BOX TO UNSWITHCHED 120V	120V OR	COMMON
	277V	(NETURAL) GROUND
OR 277V. VOLTAGE SELECTION IS MADE IN			For dimming ballast, connect
SWITCH BOX.			dimming leads to dimmer

					WALL				WHITE*	GREEN
					SWITCH
		BLK 120V								WHITE
										WHT / BLK
	BLACK
TEST					WHT / RED
		ORG 277V
SWITCH
					ORG / BLK
	BLACK	ORG/BLK
			EMERGENCY
										B	W G
			BALLAST		WHITE
		RED									ELECTRONIC
			FLEX	FLEX	WHT/BLK					A.C. BALLAST
	INVERTER		"B"	"A"	BLUE
	CONNECTOR				BLUE / WHT
	WHITE				RED					B	B Y Y R R
					YEL/BLK
	BROWN -
CHARGE					YEL
LIGHT
	VIOLET +
										BLUE
				JUNCTION
	SWITCH BOX									BLUE / WHT
				BOX
										YELLOW*
	STAB-IN CONNECTOR (2 CONDUCTORS)									YELLOW
										RED
	STAB-IN CONNECTOR (3 CONDUCTORS)									RED
	* WHITE AND YELLOW JUMPERS PROVIDED				BLUE**	BLUE**	YEL**	YEL	RED	RED
	FROM ELECTRONIC BALLAST
** (2) BLUE AND (1) RED LEADS REMOVED
	LAMPHOLDER 1									LAMPHOLDER 2
	(EMERGENCY)
							VIOLET
							TAN

®

LIGHTOLIER a GENLYTE THOMAS company.

631 Airport Road, Fall River, MA 02720