READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:FAEM3
C0506 | Page 3 of 4 |
WIRING DIAGRAM C
(2 LAMP EMERGENCY)
NOTE: FOR UNSWITCHED CIRCUIT, CONNECT BOTH WHITE/RED AND ORANGE/BLACK LEADS IN JUNCTION BOX TO UNSWITHCHED 120V OR 277V. VOLTAGE SELECTION IS MADE IN SWITCH BOX.
UNSWITCHED |
|
|
120V OR | COMMON |
|
277V | (NETURAL) | GROUND |
|
| |
|
| For dimming ballast, connect |
|
| dimming leads to dimmer |
WALL | WHITE* | GREEN |
SWITCH | ||
| WHITE | |
|
|
|
| BLACK | BLK 120V |
| ||||||||||
TEST | ORG 277V |
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
| ||||
SWITCH |
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| BLACK |
|
| ORG/BLK |
|
|
|
|
|
| |||
|
|
|
| RED |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| INVERTER |
|
|
|
|
|
|
| |||||
|
| CONNECTOR |
|
|
|
|
|
| ||||||
|
|
|
|
| ||||||||||
|
|
| WHITE |
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| ||||||
CHARGE |
|
| BROWN - |
|
|
|
|
| ||||||
LIGHT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| VIOLET + |
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| SWITCH BOX |
| ||||||||||
BALLAST
FLEX FLEX
"B" "A"
JUNCTION
BOX
|
|
|
| WHT / BLK |
|
WHT / RED |
|
|
|
| |
ORG / BLK |
|
|
|
| |
WHITE |
|
|
| B | W G |
|
|
|
| ELECTRONIC | |
|
|
|
|
| |
WHT/BLK |
|
|
| A.C. BALLAST | |
BLUE |
|
|
|
|
|
BLUE / WHT |
|
|
|
| |
RED |
|
|
| B | B Y Y R R |
YEL/BLK |
|
|
| ||
|
|
|
|
| |
YEL |
|
|
|
|
|
|
|
|
| BLUE |
|
|
|
|
| BLUE / WHT |
|
|
|
|
| YELLOW |
|
|
|
|
| YELLOW |
|
BLUE** | BLUE** | YEL | YEL | RED* |
|
RED |
| ||||
*WHITE AND RED JUMPERS PROVIDED ** (2) BLUE AND (1) RED LEADS REMOVED
FROM ELECTRONIC BALLASTLAMPHOLDER 1
(EMERGENCY)
RED** | RED |
VIOLET | LAMPHOLDER 2 |
| |
TAN |
|
C.INSTALL MOUNTING FRAME TO CEILING SUPPORT MEMBERS (See separate
D. WIRE-IN
Connect supply leads to emergency ballast, electronic | Fig. 4 |
ballast and fixture ground wire as shown in WIRING |
|
DIAGRAM A, B, or C. Cap unused lead. Close the |
|
junction box cover after wiring is completed. |
|
E. |
|
| SCREWS | SWITCH/INDICATOR | |
LIGHT BOX | ||
|
1.Cut appropriate hole size in ceiling for frame.
2.Cut hole in ceiling for SWITCH/INDICATOR LIGHT BOX in a convenient location to the side of frame (Fig. 4). The recommended hole size is
3.Close-in ceiling.
CONNECTORS
® |
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
