lNSTALIATION OF COMPACT FLUORESCENT DOWN LIGHTS AND WALL WASHERS (CONT’D)
;2;~54CL
Page 2 of 2
A. SNAPIN
Align TABS on SOCKET CUP with openings in reflector and push in SOCKET CUP until RETAINING SPRING
B. INSTALL WHITE TRIM RING
NOTE Omit this section If reflector is |
| |
1. For overlapping trim installation (Fig. 1) slip WHITE RING over |
| |
LENS TRIM as shown in Fig. 2 and 3. | REFL | |
2. For flangeless trim installation (Fig. 4), WHITE TRIM RING is not | ||
| ||
required. |
|
LENS WALL WASHER
SOCKET CUP
rJUNCTION BOX
LEAVE APPROX. 1“EXPOSED
C. PUSH-UP REFLECTOR FOR LENS WALL WASHER
1.Tilt REFLECTOR and insert SOCKET CUP into ceiling opening on side opposite JUNCTION BOX. Push REFLECTOR up leaving
approximately one inch of the REFLE~R exposed below the CEILING LINE (Fia. 10A).
2.Compress TORSl~NTITE SPRINGS on LENS TRIM by squeezing with fingem. Insert into SLOTS in REFLECTOR and push up into REFLECTOR until flush with ceiling (Fig. 11).
NOTE To remove REFLEC70R, lift LENS and pull LENS TRIM down (Fig. 12), then disengage the SOCKET CUP by daprsssing the RETAINING SPRING (Fig.5). lhrn REFLECTOR counterclockwise while pulling downward. Aftar stafling, use both hands to remove. See Fig. 7.
PUSH-UP REFLECTOR FOR OPEN WALL WASHER
1,TiltREFLECTOR and insert SOCKET CUP into ceiling opening on
side opposite JUNCTION BOX. Pivot REFLECTOR and push it up into
NOTE To remove REFLECTOR, disengage the SOCK~ CUP by daprassing the RETAINING SPRING (Fig. 5). 7urn REFLEC70R
counteroiockwise while pulling downward. After starting, use both hands to remove If dasired. Saa Fig. 7.
TITE
G
M
\
u“ WALL TO BE ILLUMINATED
FIG. 10A
OPEN WALL WASHER
JUNCTION
BOX 7
*K | ~ | b |
D.LAMPING
Line up pins and push into socket. To relamp, carefully pull lamp straight out.
CARE AND MAINTENANCE | OF A12AK@ REFLECIOR | WALL TO BE ILLUMINATED | |||||||||
If handling of reflectors with anodized or Alzak finish is required, the |
|
| |||||||||
use of clean | white | or plastic film | gloves is recommended | to avoid |
|
| |||||
fingerprints. |
|
|
|
|
|
|
|
|
| FIG. 10B | |
Anodized or Alzak surfaces can be cleaned by the following methods |
| ||||||||||
|
| ||||||||||
1. | Wipe off | with | a soft, | clean, | dry, | cloth. |
|
|
| ||
2. | Wipe off | with | a soft | clean | cloth | dampened | in mild detergent |
|
| ||
| solution. Rinse then wipe dry with |
|
| ||||||||
3. | Wipe off with a clean cloth | dampened | with | a solution | of wetting |
|
| ||||
| agent and water (such as 2 oz. per gallon |
|
| ||||||||
| Wyandotte Products). Then wipe dry. |
|
|
|
|
| |||||
4. | Or use a liquid wash such | as Glass Wax”. Avoid gritty | cleaning |
|
| ||||||
| agents. |
|
|
|
|
|
|
|
|
|
|
FIG. 11
/-- ‘“’%lON
SOCKET
CUP
-Qi-REFLEcTOR
FIG. 13 | FIG. 12 |