INSTRUCTION SHEET NO.

 

 

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

 

 

 

 

 

 

 

 

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To

 

 

IS:4X4 LC

 

 

 

assure full compliance with local codes and regulations, check with your local electrical inspector before

 

 

 

 

 

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

 

 

 

 

 

Retain these instructions for maintenance reference.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A0602

 

Page 2 of 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B. ADJUST FIK

Set FIK so that bottom edge is flush to, or recessed 1/8” above finished ceiling (Fig. 8).

Final vertical adjustment may be made by means of ADJUSTMENT SCREWS on inside of FIK.

C. CLOSE-IN

Close-in and finish ceiling as required.

ADJUSTMENT

ADJUSTABLE

SCREWS

MOUNTING

 

BRACKET

FIK

 

FLUSH TO CEILING OR

 

UP TO 1/8” RECESSED

 

 

FINISHED

 

CEILING

 

FIG. 8

FIG. 9

Base of FIK is provided with a

hole pattern (Fig. 9) to assist with the alignment of multiple FIK’s. This hole pattern will facilitate the use of laser beams, plumb lines, etc.

D.INSTALLATION OF REFLECTOR TRIM FOR STANDARD AND CHICAGO PLENUM UNITS

1.Squeeze both TORSION SPRINGS and insert ends into

EMBOSSED SLOTS.

2.Push REFLECTOR TRIM up into FIK until flange is seated firmly against ceiling surface.

**Care and Maintenance of “Alzak” REFLECTOR TRIM finish:**

If handling of REFLECTOR TRIM with anodized or Alzak finish is required, the use of clean white or plastic film gloves is recommended to avoid fingerprints.

Anodized or Alzak surfaces can be cleaned by the following methods:

1.Wipe off with a soft, clean, dry, lint-free cloth.

2.Wipe off with a soft clean cloth dampened in mild detergent solution. Rinse, then wipe dry with lint-free cloth or paper towel.

3.Wipe off with a clean cloth dampened with a solution of wetting agent and water (such as 2 oz. Per gallon “Pluronic L62-LF” by Wyandotte Products). Wipe dry.

4.Use a liquid wax such as Glass Wax. Avoid gritty cleaning agents.

TORSION

SPRING

EMBOSSED

SLOT

REFLECTOR

TRIM

FIG. 10

E. RE-LAMPING

1.Turn off power

2.Pull REFLECTOR TRIM down until ends of TORSION SPRINGS reach EMBOSSED SLOTS.

3.Squeeze TORSION SPRINGS to disengage from EMBOSSED SLOTS, and remove REFLECTOR TRIM.

4.Replace lamp (Do not exceed maximum wattage marking).

5.Replace REFLECTOR TRIM.

F. BALLAST REPLACEMENT

1.Make sure AC power is OFF at fuse-box.

2.Remove reflector trim & lamp(s) (See E.).

3.Undo wingnut(s) and remove upper reflector.

4.Remove ballast access plate from housing.

5.Remove screws that secure ballast to junction box cover, pull Ballast through opening into fixture.

6.Disconnect wire leads from ballast push-in terminals. (Insert pin or paper clip in RELEASE SLOT, Fig. 11)

7.Remove ballast from mounting plate, and install new ballast.

8.Insert wire leads into ballast. Follow wiring diagram on

BALLAST. 90°

9.Reattach ballast access plate, upper reflector, lamp(s), and reflector trim.

NUTS

BALLAST

HOUSING

PLATE

WINGNUT

 

UPPER

 

REFLECTOR

 

 

 

 

A

RELEASE

SLOT

FIG. 11

BALLAST

FIG. 12

COMPANY

631 Airport Road, Fall River, MA 02720

Page 2
Image 2
Lightolier IS:4X4LC instruction sheet Adjust FIK, Close-In, Re-Lamping, Ballast Replacement

IS:4X4LC specifications

The Lightolier IS:4X4LC is a cutting-edge lighting solution designed to meet the needs of both commercial and residential spaces. This innovative fixture represents a blend of modern aesthetics and advanced technology, making it a popular choice for architects, designers, and homeowners alike.

One of the main features of the IS:4X4LC is its unique design, which allows for a sleek and unobtrusive installation into ceilings. With a dimension of 4x4 feet, this fixture provides an expansive area of illumination, ideal for large rooms, conference areas, and retail spaces. Its minimalist appearance complements a variety of interior styles, ensuring it can seamlessly integrate into diverse environments.

The IS:4X4LC incorporates state-of-the-art LED technology, which brings numerous benefits over traditional lighting solutions. LED components are more energy-efficient, consuming significantly less power while providing a brighter output. This efficiency translates into reduced energy costs, making it an environmentally responsible choice. Additionally, LEDs have an extended lifespan, often lasting up to 50,000 hours, which means less frequent replacements and maintenance.

Another highlight of the IS:4X4LC is its versatility. It supports various dimming options, allowing users to adjust the brightness to suit different occasions or moods. This feature is particularly useful in settings like conference rooms, where lighting needs might change throughout the day. The fixture’s compatibility with smart lighting systems further enhances its adaptability, enabling remote control and automation through mobile devices or home assistant platforms.

Furthermore, the IS:4X4LC promotes excellent light distribution and quality. Designed to minimize glare, it provides a comfortable lighting experience that is beneficial for visual tasks. This makes it an ideal choice for workspaces, schools, and retail environments where clear visibility is crucial.

In terms of installation, the IS:4X4LC comes with user-friendly mounting options, making the process straightforward for electricians and DIY enthusiasts. The fixture is also designed with heat management in mind, ensuring that it operates efficiently without overheating.

In summary, the Lightolier IS:4X4LC stands out for its stylish design, energy efficiency, versatility, and exceptional light quality. Its combination of modern technology with practical functionality makes it a top choice for anyone looking to enhance their space with effective and attractive lighting solutions.