Lincoln 1117-080-A, 1162-080-A, 1132-080-A, 1131-08H-A, 1132-08H-A, 1116-080-A1, 1130-08H-A Phase

	1130-080-A		120/208VAC	60 HZ.	1 PHASE
	1130-080-A1		120/208VAC	60 HZ.	1 PHASE
	1130-08H-A		208 VAC	60 HZ.	1 PHASE
	1131-080-A		120/240VAC	60 HZ.	1 PHASE
	1131-080-A1		120/240VAC	60 HZ.	1 PHASE
	1131-08H-A		240 VAC	60 HZ.	1 PHASE
	1132-080-A		120/208VAC	60 HZ.	3 PHASE
	1132-080-A1		120/208VAC	60 HZ.	3 PHASE
	1132-08H-A		208 VAC	60 HZ.	3 PHASE
	1133-080-A		120/240VAC	60 HZ.	3 PHASE
	1133-080-A1		120/240VAC	60 HZ.	3 PHASE
	1133-08H-A		240 VAC	60 HZ.	3 PHASE
	1161-080-A		120/240VAC	60 HZ.	1 PHASE
	1162-080-A		120/208VAC	60 HZ.	3 PHASE
SYMPTOM		POSSIBLE CAUSE		EVALUATION
Oven fan will not run		Incoming power supply		Check circuit breakers. Reset if required. Call
				power co. if needed.
		Fuses, 10 Amp, motor and		Check, replace if necessary.
		controls
		Fuse holder		Check, replace if necessary.
		Hi-limit thermostat,		Terminals are normally closed. If open, reset
		Oven cavity		thermostat and retest. If thermostat will not hold
				for maximum oven temperature, and oven is not
				exceeding temperature setting, check for proper
				location of capillary bulb in its spring holder. If the
				capillary checks okay, replace the hi-limit
				thermostat.
		Switch, main power		Check continuity between switch terminals.
				Replace switch as needed.
		Relay, oven start		Check for 120VAC supplied to coil of relay. If no
				voltage is present, trace wiring back to main
				power switch. If voltage is present, check for pull
				in of relay contacts. Replace relay as needed.
		20 minute time delay		Check for 120VAC at terminal #1 to neutral on
				time delay relay. If voltage is not present, trace
				wiring back to 10A. fuse. If voltage is present at
				terminal #1, check for 120VAC at terminal #2 to
				neutral. If no voltage is present, and oven start
				relay is closed, replace 20 minute time delay relay.
		Relay, main fan		Check for 120VAC to coil of main fan relay. If no
				voltage is present, trace wiring back to 20 minute
				time delay relay. If voltage is present, check to
				insure that relay contacts are closing. Replace
				relay as needed.
		Main fan motor		Check for supply voltage at motor. If no voltage is
				present, trace wiring back to main fan relay.
				WITH POWER OFF: Check for opens, shorts or
				grounds. Turn fan blade to check for locked rotor.
		Capacitor		Check for shorts or grounds.
				WARNING: Capacitor has a stored charge,
				discharge before testing.
No main fan cool down		20 Minute time delay		Check for 120VAC at terminal #2 to neutral while
				the oven is ‘on’. Turn off the main fan switch,
				120VAC should continue to be present for 20
				minutes. If voltage is not present for approx. 20
				minutes, replace the 20 minute time delay.
		Oven fan relay		Check for 120VAC to relay coil, if no voltage is
				present, trace wiring back to 20 minute time delay.
				If voltage is present, be sure that relay contacts
				stay closes during the 20 minute cool down.

16 Impinger II – Advantage Digital Express Service Manual - Domestic