Lindy 51246 technical specifications Pin Assignments, Technical Specifications, Introduction

PCIe Low Profile 1P (IEEE 1284)

User Manual English

LINDY No. 51246

www.lindy.com

0	13	0	1409	7168 Simple COMM. 10
				Controller

If the Vendor ID, Device ID, Device Class or IRQ aren’t displayed or an error occurs, please try another PCI slot.

Once the hardware has installed correctly you can start installing the software from the driver CD.

Pin Assignments

Parallel 25 Pin female connector pin assignments:

Parallel 25 Pin female connector :

Pin	Signal	Pin	Signal	Pin	Signal
1	STROBE	10	ACKNOWLEDGE	19	GROUND
2	DATA 0	11	BUSY	20	GROUND
3	DATA 1	12	PAPER EMPTY	21	GROUND
4	DATA 2	13	SELECT	22	GROUND
5	DATA 3	14	AUTO FEED	23	GROUND
6	DATA 4	15	ERROR	24	GROUND
7	DATA 5	16	INIT	25	GROUND
8	DATA 6	17	SELECT INPUT	26	GROUND
9	DATA 7	18	GROUND

Technical Specifications

∙Support x17 x1,x2,x4,x8,x16（lane）PCI-Express Bus connector keys

∙Operating system: DOS, WIN 9.x, ME, NT, 2000, XP, 2003 Server, VISTA, Win7, LINUX,

∙Support ECP, EPP and SPP

∙Ready of the Intel and AMD 32/64-bit CPU System

∙Built-in 32 byte hardware FIFO

∙IRQ and IO address assigned by System

∙Certified by Microsoft WHQL, CE, FCC approval

∙PCB: 80 x 65 mm

Introduction

Thank you for purchasing the LINDY PCIe Low Profile one Port parallel Card. This card is equipped with one 1284 centronics parallel interface. The parallel port include IEEE1284 with speeds up to 15MB/Sec on the Parallel port.

Port Specification

Parallel Port:

∙Chipset: Oxford 952

∙IEEE standard: IEEE 1284 Interface

∙Max. Speed: Up to 15MB/Sec

∙DB 25 Female Connector

Package Contents

￿1 x LINDY PCIe Low Profile 1P Card

￿LINDY User manual

￿LINDY Driver CD

Installation

1.Turn off the power of your computer and remove the power cable

2.Install the PCIe Low Profile card into an available PCIe Low Profile slot in your computer

3.Connect the peripheral ie Printer, Modem, etc. to the adapters port

4.Re-connect the power cable & turn on the power of your computer

PCI device listing display (for example…)

Bus	Device	Func	Vendor ID	Device	Device Class	IRQ
No	No	No		ID
0	7	1	8086	7010	IDE Controller	14

Certifications

FCC Certifications

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation.

CE Certification

This equipment complies with the requirements relating to electromagnetic compatibility, EN 55024 and EN55022 class A for ITE, EN61000-3-2/-3 the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility.

Recycling Information

WEEE (Waste of Electrical and Electronic Equipment),

Recycling of Electronic Products

United Kingdom

In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process.

Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways. Please follow your