6. | ROUTE THE CABLE |
| 7. CONNECT THE CABLE & SET THE DEVICE ADDRESS | 8. MOUNT THE KEYPAD | ||||
| EACH |
|
|
|
| 1 HOOK THE KEYPAD ASSEMBLY | ||
|
|
|
|
| FOLLOW THIS WIRING DIAGRAM |
| ||
|
|
|
|
|
| ONTO THE MOUNTING PLATE | ||
| CABLE LENGTH FORMULA FOR EACH KEYPAD USED IN THE SYSTEM |
| TO CONNECT THE KEYPAD |
| ||||
|
|
|
| |||||
|
|
|
|
| TO THE CONTROLLER |
| 2 INSTALL THE | |
|
|
|
|
|
|
|
| |
|
|
|
|
| PWR | PWR |
| TWO SCREWS |
| CABLE RUN | CABLE TYPE | FORMULA |
|
|
| ||
|
| GND | GND ACCESS CONTROL |
| ||||
|
|
|
|
|
| |||
300 FEET MAXIMUM | BELDEN 9931 (24 AWG) | FEET x LOAD UNITS < 3,000 MAXIMUM | DAT1 | DAT1 | SYSTEM PBUS |
| ||
TERMINALS DAT0 | DAT0 |
| ||||||
TERMINALS |
| |||||||
|
|
|
|
| ||||
|
|
|
|
| DVAL | DVAL |
| |
500 FEET MAXIMUM | WEICO 9405 (20 AWG) | FEET x LOAD UNITS < 10,000 MAXIMUM |
|
|
| |||
| PCLK | PCLK |
|
| ||||
|
|
|
|
|
|
| ||
|
|
|
|
|
| EACH REMOTE DEVICE |
| |
|
|
|
|
|
| MUST BE SET TO A |
| |
|
|
|
|
|
| UNIQUE NUMBER |
| |
|
|
|
| SET THE DEVICE | FROM 1 TO 6 |
|
| |
|
|
|
|
|
|
| ||
|
| HOMERUN WIRE FROM THE | ADDRESS SWITCH |
|
|
| ||
|
|
|
|
|
|
| ||
|
| CONTROLLER TO EACH |
|
|
|
|
| |
|
| KEYPAD’S LOCATION |
|
|
|
|
| |
|
| (1000 FEET WIRE MAXIMUM |
|
|
|
|
| |
|
| ALLOWED IN THE SYSTEM) | CAUTION |
|
| 3 | ||
|
|
|
|
|
| |||
|
|
|
| TO PROTECT THE KEYPAD FROM |
| FIT THE BOTTOM TAB OF | ||
|
|
|
|
| THE FACEPLATE INTO THE | |||
|
|
|
| STATIC DISCHARGES, BE SURE |
|
| ||
|
|
|
|
|
| SLOT ON THE KEYPAD | ||
|
|
|
| EARTH GROUND IS CONNECTED | ARROW ON SWITCH SLOT | 4 | ||
|
|
|
| TO THE CONTROLLER | POINTS TO THE NUMBER | SNAP THE TOP | ||
|
|
|
| FOR LOCAL POWER, DISCONNECT RED WIRE FROM "PWR" CONNECTION ON | ||||
|
|
|
| OF THE KEYPAD | ||||
|
|
|
| AND CONNECT EXTERNAL 12 VDC POWER SUPPLY (+ TO PWR & - TO GND) | INTO PLACE | |||
|
|
|
| NOTE: CONTROLLER MUST STILL BE CONNECTED TO |
| |||
9. | PROGRAM THE SYSTEM |
| 10. TEST THE KEYPAD |
|
| LINEAR LIMITED WARRANTY | ||
|
|
|
|
| 1 | THE RED INDICATOR |
| This Linear product is warranted against defects in material and workmanship for twelve |
|
|
| PROGRAM THE CONTROLLER |
|
| (12) months. This warranty extends only to wholesale customers who buy direct from Linear | ||
|
|
|
|
| SHOULD BE LIT |
| or through Linear’s normal distribution channels. Linear does not warrant this product to | |
|
|
| TO CONFIGURE THE PBUS |
| 2 |
|
| consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s |
|
|
| DEVICE |
| ENTER A VALID CODE |
| warranty, if any. There are no obligations or liabilities on the part of Linear LLC for consequential | |
|
|
|
|
| damages arising out of or in connection with use or performance of this product or other indirect damages | |||
|
|
|
|
|
|
|
| |
|
|
|
|
| 3 | THE RED INDICATOR SHOULD TURN | with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All | |
|
|
|
|
| implied warranties, including implied warranties for merchantability and implied warranties | |||
|
|
|
|
|
| GREEN AND THE PROGRAMMED | for fi tness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu of all other | |
|
|
|
|
|
| RELAY IN THE CONTROLLER | warranties express or implied. | |
|
|
|
|
|
| SHOULD ACTIVATE |
| All products returned for warranty service require a Return Product Authorization Number |
|
|
|
|
|
|
|
| (RPA#). Contact Linear Technical Services at |
|
|
|
|
|
|
|
| important details. |
FCC NOTICE
Changes or modifications not expressly described in this manual or approved by the manufacturer could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
| • Increase the separation between the equipment and receiver. |
|
| • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. | |
| • Consult the dealer or an experienced radio/TV technician for help. |
|
| THE YELLOW INDICATOR LIGHTS WHEN |
|
REFER TO THE CONTROLLER | THE KEYPAD IS LOCKED OUT OR BUSY |
|
|
| |
PROGRAMMING INSTRUCTIONS |
|
|
FOR DETAILS | Copyright © 2012 Linear LLC | 218940 B |
| ||
