Manuals / Linear / Baby / Safety Gate

Linear SWC, SWR, SWD Auxiliary Relay Mode, Reverse Delay Time, Low Power Mode, Power Failure Mode

Models: SWR SWD SWC

1 32
Download 32 pages 20.17 Kb
Page 17
Image 17

Advanced Controller Programming (Cont.)

Auxiliary Relay Mode

The Auxiliary Relay has normally open and normally closed contacts. The factory setting disables the Auxiliary Relay. The relay can be set for:

• Maglock: The relay will energize during any pending or actual gate

motion (open only), to deactivate a magnetic or solenoid gate lock.

• Ticket Dispenser: The relay will be energized at all times (enabling

a ticket dispenser) unless the operator is fully open or in an

entrapment condition.

• Strobe: The relay will energize during any pending or actual gate

motion (either open or close), to activate a warning strobe light.

• Alarm: The relay will energize if the gate is manually forced open

from the full closed position.

FUNCTION

"AR"

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO SELECT AN OPTION

AUXILIARY

RELAY MODE

OPTIONS

AUXILIARY RELAY DISABLED

AUXILIARY RELAY USED FOR

MAGLOCK CONTROL

AUXILIARY RELAY USED FOR

TICKET DISPENSER CONTROL

AUXILIARY RELAY USED FOR

WARNING STROBE LIGHT

AUXILIARY RELAY USED FOR

CONNECTION TO ALARM DEVICE

Reverse Delay Time

The factory default sets the Reverse Delay to 1 second. The operator will wait the length of the delay before reversing direction. This feature will not change the reversal time when the operator is responding to an entrapment condition from an obstruction input or inherent entrapment protection sensor. The Reverse Delay can be set from 1 to 9 seconds. Heaver gates require a longer delay to allow time for the gate to stop.

Low Power Mode

FUNCTION

"RD"

REVERSE

DELAY TIME

OPTIONS

SET TIMER VALUE 1 TO 9 SECONDS

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO

SELECT AN OPTION

This function is only used with DC swing gate Model SWD. The factory default disables the Low Power Mode. When Low Power Mode is enabled, and AC power fails, the controller will assume Low Power Mode after 60 seconds of gate inactivity. Low power mode turns off all accessory power and indicators. Only inputs from the radio receiver, reverse loop, or restoring AC power will wake the Controller from Low Power Mode. Programming Mode can still be accessed while the Controller is in Low Power Mode.

✓NOTE: This function will only be displayed in Model SWD operators.

Power Failure Mode

This function is only used with DC swing gate Model SWD. The factory default is set for Fail Safe, alternately the Controller can be set for Fail Secure, Open Immediate, or Close Immediate.

 

FUNCTION

 

OPTIONS

 

 

 

 

 

"LP"

 

 

 

LOW POWER MODE DISABLED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LOW POWER MODE ENABLED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PRESS UP OR

 

 

 

 

 

 

DOWN TO CYCLE

 

 

 

 

 

 

THROUGH OPTIONS

 

 

 

 

 

 

 

 

 

 

 

 

LOW POWER

PRESS ENTER TO

MODEL SWD

 

 

MODE

SELECT AN OPTION

ONLY

 

 

 

 

 

 

•Fail Safe: If the AC power fails and the battery voltage drops below approximately 22 Volts, 5 seconds later the operator will cycle open if not already open. When AC power is restored, or the battery gets charged by solar panels, the operator will resume normal operation and auto-close if programmed to do so.

•Fail Secure: If the AC power fails and the battery voltage drops below approximately 22 Volts, 5 seconds later the operator will cycle closed if not already closed. When AC power is restored, or the battery gets charged by solar panels, the operator will resume normal operation.

✓NOTE: Fail Safe and Fail Secure are disabled if Stagger Mode is enabled.

•Open Immediate: If the AC power fails, the operator will cycle open if not already open and cease operation. When AC power is restored, the operator will resume normal operation and auto-close if programmed to do so.

•Close Immediate: If the AC power fails, the operator will cycle closed if not already closed and cease operation. When AC power is restored, the operator will resume normal operation.

✓NOTE: This function will only be displayed in Model SWD operators.

FUNCTION

"FS"

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO SELECT AN OPTION

POWER

FAILURE MODE

OPTIONS

SET TO FAIL SAFE MODE

SET TO FAIL SECURE MODE

SET TO OPEN IMMEDIATE MODE

SET TO CLOSE

MODEL SWD

IMMEDIATE MODE

ONLY

SWR • SWC • SWD Swing Gate Operator Installation Guide

- 15 -

227965 Revision X13 3-28-2008

Page 16 Page 18
Page 17
Image 17
Linear SWC, SWR, SWD manual Auxiliary Relay Mode, Reverse Delay Time, Low Power Mode, Power Failure Mode
Page 16 Page 18

SWR, SWD, SWC specifications

Linear SWC (Single Wire Control), SWD (Single Wire Debug), and SWR (Single Wire Radio) are advanced communication protocols widely utilized in embedded systems and electronic applications. These protocols enhance the efficiency of data transmission, reduce the number of physical connections required, and simplify the design process for developers.

The main feature of Linear SWC is its ability to transmit control signals over a single wire, allowing for straightforward connectivity between microcontrollers and various peripherals. This approach minimizes the complexity of printed circuit boards (PCBs) and reduces the space needed for connections, making it ideal for compact designs. Linear SWC operates based on a master/slave architecture, where the master device initiates communication, and the slave devices respond.

SWD, primarily used for debugging embedded systems, is a two-pin interface that supports high-speed data transfer with minimal pin usage. Unlike traditional JTAG, SWD is simpler and more efficient, allowing developers to perform debugging and programming tasks with fewer resources. The SWD protocol offers features such as breakpoint management, memory read/write capabilities, and real-time variable monitoring, empowering developers to optimize their code and increase debugging efficiency.

SWR is focused on wireless communication, leveraging a single wire for transmitting radio signals. This technology is particularly advantageous in applications requiring minimal hardware while maintaining robust connectivity. SWR supports various modulation techniques and can operate in different frequency bands, making it versatile for various use cases. The single-wire approach reduces the complexity of antenna design and enhances the overall reliability of wireless communications in challenging environments.

One of the key characteristics shared by SWC, SWD, and SWR is their ability to reduce power consumption. By minimizing the number of connections and optimizing signal paths, these protocols significantly decrease the energy required for data transmission. Additionally, their compatibility with a wide range of microcontrollers and integrated circuits contributes to their widespread adoption in modern electronic designs.

In summary, Linear SWC, SWD, and SWR serve critical roles in the evolution of embedded systems, offering unique features, advanced technologies, and efficient characteristics. Their capability to simplify designs, reduce power consumption, and enhance overall communication quality makes them essential tools for engineers and developers in today's fast-paced technological landscape. As the demand for compact, efficient solutions grows, these protocols are poised to play an increasingly significant role in future innovations.